Final Architectural Plans

O. 2. FB = 1450 PSI; E= 1,700,000 PSI FOR MEMBERS 2"-4" THICK, 2"-4" WIDE AND FB = 1250 PSI FOR MEMBERS 2" TO 4" THICK, AND 5" AND WIDER. A. MAXIMUM MOISTURE CONTENT: 19% B. ALL LUMBER IN CONTACT WITH MASONRY OR EXPOSED TO EXTERIOR SHALL BE PRESSURE TREATED, "WOLMANIZED" BY KOPPERS OR APPROVED EQUAL. 2. ROUGH HARDWARE, NAILS, SCREWS, BOLTS, ETC. AS REQUIRED FOR JOB CONDITION OR AS SHOWN AND SPECIFIED. 3. BUILT-UP GIRDERS - LAMINATED VENEER LUMBER A. "MICRO-LAMS" AS MANUFACTURED BY TRUS JOIST, INC. OR EQUAL B. STORE IN CLEAN, DRY, AREA. EXERCISE CARE IN HANDLING TO PREVENT DAMAGE. 4. PLYWOOD - COMPLY WITH DOC PSI, HPMA PS51, APA E30, APA Y510, AND HPMA HP-S6. A. N.A. B. USE PRESSURE TREATED PLYWOOD IN ACCORDANCE WITH AWPB LP-2 WHERE NOTED OR REQUIRED. 5. MISCELLANEOUS A. RAILS SHALL BE INSTALLED IN THE SHAPES, SIZES, AND LOCATIONS AS SHOWN ON THE DRAWINGS INCLUDING, BUT NOT LIMITED TO, STAIRS, BALCONIES, ETC. I. ALL RAILS SHALL BE SECURELY FASTENED TO THE BUILDING STRUCTURE AND DESIGNED IN ACCORDANCE WITH ALL APPLICABLE CODES AND ORDINANCES INCLUDING, BUT NOT LIMITED TO, IBC, ANSI, ETC. II. WOOD FOR INTERIOR RAILS SHALL BE SOLID SELECT PIPE MILLED TO THE PROFILES AS REQUIRED AND SANDED SMOOTH. III. WOOD FOR EXTERIOR RAILS SHALL BE OF SOUND PINE OR FIR PRESSURE TREATED WITH WOLMAN SALTS AND SANDED SMOOTH. C. EXECUTION 1. FRAMING A. LAY OUT, CUT, FIT AND ERECT FRAMING FOR ROUGH AND FINISHED WORK, BLOCKING, NAILERS, FURRING AND ALL OTHER ROUGH CARPENTRY. DO CUTTING WORK IN CONNECTION WITH CARPENTRY AND FINISH FOR OTHER TRADES. BRACE, PLUMB, AND LEVEL ALL MEMBERS IN TRUE ALIGNMENT AND RIGIDLY SECURE IN PLACE WITH SUFFICIENT NAILS, SPIKES, SCREWS, AND BOLTS AS NECESSARY. DEFECTS WHICH RENDER ANY PIECE OR PART UNABLE TO SERVE ITS INTENDED PURPOSE SHALL BE DISCARDED, OR IF IN PLACE, CUT OUT AND REPLACED. B. PROVIDE WOOD FURRING AND SUSPENSION NECESSARY TO RECEIVE AND SUPPORT FINISHES SUCH AS PLYWOOD, INSULATION, WALL SURFACING, MILLWORK, FINISH, CARPENTRY, AND CUSTOM WOODWORK. MEMBERS SHALL BE OF SIZE NECESSARY TO PROVIDE ADEQUATE BRACING, SUPPORT, AND FASTENING. SOFFIT AREAS SHALL BE TIED TOGETHER AND TO ADJOINING AND SUPPORTING CONSTRUCTION AS REQUIRED. C. PROVIDE WOOD ROUNDS, NAILING STRIPS, BLOCKING AND SIMILAR ITEMS WHEREVER NECESSARY OR REQUIRED THROUGHOUT THE PROJECT FOR THE SUPPORT, PROPER ERECTION OR INSTALLATION OF ALL WORK INCLUDING, BUT NOT LIMITED TO

WOOD ROUNDS, NAILING STRIPS, BLOCKING AND SIMILAR ITEMS WHEREVER NECESSARY OR REQUIRED THROUGHOUT THE PROJECT FOR THE SUPPORT, PROPER ERECTION OR INSTALLATION OF ALL WORK INCLUDING, BUT NOT LIMITED TO MIRRORS, CABINETS, CLOSETS, SHELF CLEATS, BASES, ETC. THOROUGHLY SECURE IN PLACE BY APPROVED MEANS. D. JOIST FRAMING FROM OPPOSITE SIDES OF AND SUPPORTED ON A FASTENED OR BUTTED END- TO END AND TIED BY METAL STRAPS. WHERE JOISTS BUTT INTO FLUSH MOUNTED BEAM OR GIRDER, PROVIDE METAL JOIST HANGERS AT EACH JOIST IN WIDTHS AS REQUIRED FOR BY FRAMING AND AS SHOWN OR SPECIFIED. E. ALL BUILT-UP BEAMS, GIRDERS POSTS TO BE SPIKED AT 12" ON CENTER AND FASTENED TO SUPPORTS WITH 2 1/2" BOLTS. NO FACE SPLITS SHALL BE ALLOWED ON GIRDERS. I. BEAMS, GIRDERS AND OTHER CONCENTRATED LOADS SHALL BEAR ON SOLID MASONRY OR FILLED CORES OF BLOCK. F. FRAMINGS AROUND FLUES AND CHIMNEYS: COMBUSTIBLE FRAMING SHALL BE TRIMMED NOT LESS THAN 2" FROM FLUES AND CHIMNEYS AND 6" AWAY FROM FLUE OPENINGS. G. FOUNDATION AROUND ANCHORAGE: WALL SILL PLATES SHALL BE ANCHORED TO FOUNDATION WALLS WITH 1/2" DIAMETER ANCHOR BOLTS EMBEDDED NOT LESS THAN 16" IN GROUTED UNIT MASONRY. PROVIDE MIN. 2 ANCHOR BOLTS PER PLATE, PLACED 1'-0" MAX. FROM ENDS AND SPACED 6'-0" ON CENTER MAXIMUM. SILL PLATES BEARING ON MASONRY SHALL BE WOLMANIZED. D. STAIRS A. PROVIDE WOOD STAIRS WHERE SHOWN. B. STAIRS SHALL BE CONSTRUCTED TO SUPPORT THE DEAD LOAD IN ADDITION TO THE LIVE LOAD OF 100 PSF WITH A LEGAL FACTOR OF SAFETY, AND SHALL MEET ALL REQUIREMENTS OF THE LAWS AND THE APPROVAL OF THE AUTHORITIES HAVING JURISDICTION. C. INSTALL STAIRS IN ACCORDANCE WITH ALL APPLICABLE CODES AND ORDINANCES INCLUDING, BUT NOT LIMITED TO, IBC, ANSI. D. INSTALLATION SHALL BE RIGID, SUBSTANTIAL CONSTRUCTION THROUGHOUT, PLUMB AND TRUE TO EXACT LINES AND LEVELS, POSITIONED IN CORRECT LOCATIONS AND IN PROPER RELATION TO ADJOINING WORK. E. ALL FASTENINGS SHALL BE CONCEALED. E. MILLWORK 1. GENERAL A. WORK OF THIS SECTION, AS SHOWN OR SPECIFIED, SHALL BE IN ACCORDANCE WITH THE REQUIREMENTS OF THE CONTRACT DOCUMENTS B. QUALITY ASSURANCE: QUALIFICATIONS OF FABRICATORS AND INSTALLERS: FOR ACTUAL FABRICATION AND INSTALLATION OF CABINETRY AND MILLWORK, USE ONLY PERSONNEL WHO ARE THOROUGHLY TRAINED AND EXPERIENCED IN PRODUCTS INVOLVED AND IN THE RECOMMENDED METHODS FOR THEIR FABRICATION AND INSTALLATION. 2. SUBMITTALS A. SHOP DRAWINGS: BEFORE ANY

RK, USE ONLY PERSONNEL WHO ARE THOROUGHLY TRAINED AND EXPERIENCED IN PRODUCTS INVOLVED AND IN THE RECOMMENDED METHODS FOR THEIR FABRICATION AND INSTALLATION. 2. SUBMITTALS A. SHOP DRAWINGS: BEFORE ANY CABINETRY AND MILLWORK ARE FABRICATED AND DELIVERED TO THE JOB SITE, SUBMIT COMPLETE SHOP DRAWINGS TO THE OWNER FOR APPROVAL. 3. PRODUCTS A. CUT ALL OPENINGS FOR EQUIPMENT. COMPLY WITH MANUFACTURERS REQUIREMENTS. SEAL EDGES OF ALL CUTS. B. PROVIDE COMPLETE HARDWARE AS REQUIRED TO COMPLETE THE JOB. HARDWARE DESIGN AS SELECTED BY OWNER. HARDWARE STANDARDS SHALL COMPLY WITH ANSI A156.9 4. INSTALLATION A. INSTALL THE WORK PLUMB, LEVEL, TRUE AND STRAIGHT, WITH NO DISTORTIONS. SHIM AS REQUIRED USING CONCEALED SHIMS. INSTALL TO A TOLERANCE OF 1/8" IN 8'-0" FOR PLUMB AND LEVEL AND WITH 1/16" MAX. OFFSET IN FLUSH ADJOINING SURFACES. B. SCRIBE AND CUT WORK TO FIT ADJOINING WORK, AND REFINISH CUT SURFACES OR REPAIR DAMAGED FINISH AT CUTS. C. ANCHOR WOODWORK TO ANCHORS OR BLOCKING BUILT-IN OR DIRECTLY ATTACHED TO SUBSTRATES. SECURE TO GROUNDS, STRIPPING AND BLOCKING WITH COUNTERSUNK, CONCEALED FASTENERS AND BLIND NAILS AS REQUIRED FOR A COMPLETE INSTALLATION. 5. PROTECTION A. COVER CASEWORK WITH 4-MIL POLYETHYLENE FILM, FOR PROTECTION AGAINST SOILING AND DETERIORATION DURING REMAINDER OF CONSTRUCTION PERIOD. F. WORKMANSHIP 1. ALL MANUFACTURE'S ASSOCIATIONS SPECIFICATIONS SHALL APPLY FOR FRAMING, CABINETRY, STAIRS, ETC. 2. ALL WOODWORK SHALL BE FINISHED SMOOTH, HAND SANDED ON ALL EXPOSED SURFACES, FREE FROM DEFECTS, DIRT, STAINS, ETC. 3. ALL WOODWORK SHALL BE ERECTED IN A THOROUGHLY WORKMANLIKE MANNER. 4. ALL ASSEMBLING SHALL BE CLEANLY CUT, TRUE, AND TIGHTLY FITTED. 5. ALL NAILING SHALL BE DONE IN SUCH A MANNER AS TO PREVENT ANY DAMAGE TO THE FINISHED SURFACES. No. Date Description

PRINCIPAL IN CHARGE PROJECT TEAM CHECKED BY SHEET DESCRIPTION ISSUED FOR: SHEET NUMBER COPYRIGHT © JORGE MASTROPIETRO ATELIER ARCHITECTS JORGE E. MASTROPIETRO NY LICENSE NO. 036208-1 ARCHITECT: OWNER: CONSULTANTS: DOB APPROVAL STAMP: ARCHITECT'S SEAL: PROJECT: JENNIFER PALERMO NJ LICENSE NO. AI 015932 262-270 MAIN STREET WEST ORANGE ESSEX COUNTY, NJ 07052 BLOCK 114 LOT 50 & 55 262 MAIN STREET REALTY LLC 262-270 MAIN STREET WEST ORANGE, NJ 07052 646 427 9908 A0.01D GENERAL NOTES JM CC JM PROGRESS DATE: 03-09-2026 TRAFFIC ENGINEER DOLAN&DEAN CONSULTING ENGINEERS, LLC 181 WEST HIGH STREET SOMERVILLE, NJ 08876 908 927 0100 STRUCTURAL ENGINEER HUDSON ENGINEERING, LLC. 25 W8TH STREET, BSMT BAYONNE, NJ 07002 201 614 5304 CIVIL ENGINEER HUDSON ENGINEERING, LLC. 25 W8TH STREET, BSMT BAYONNE, NJ 07002 201 614 5304 CONSTRUCTION NOTES 1. GENERAL: ALL WORK TO BE COMPLETED IN ACCORDANCE WITH THE 2021 INTERNATIONAL BUILDING CODE - NJ EDITION, AND REGULATIONS OF ALL OTHER AGENCIES HAVING JURISDICTION. 2. MEANS OF EGRESS: ALL MEANS OF EGRESS SHALL BE MAINTAINED CLEAR AND FREE OF ALL OBSTRUCTIONS, SUCH AS BUILDING MATERIALS, TOOLS, ETC. 3. FIRE SAFETY: A. ALL BUILDING MATERIALS WHICH ARE STORED AT THE SITE OR ANY AREA OF THE BUILDING ARE TO BE STORED IN A LOCKED AREA. ACCESS TO THE AREA TO BE CONTROLLED BY THE GENERAL CONTRACTOR OR HIS REPRESENTATIVE. B. ALL MATERIALS TO BE STORED IN A ORDERLY FASHION. C. ALL FLAMMABLE MATERIALS TO BE KEPT TIGHTLY SEALED IN THEIR RESPECTIVE MANUFACTURERS' CONTAINERS. SUCH MATERIALS ARE TO BE KEPT AWAY FROM HEAT. D. ALL FLAMMABLE MATERIALS TO BE USED AND STORED IN AN ADEQUATELY VENTILATED SPACE. E. ALL ELECTRICAL POWER TO BE SHUT OFF WHERE THERE ARE EXPOSED CONDUITS. F. ALL ELECTRICAL POWER IN THE CONSTRUCTION AREA TO BE SHUT OFF AFTER WORKING HOURS. G. CONTRACTOR, AT ALL TIMES, IS TO ENSURE THERE IS NO NATURAL GAS LEAKAGE IN THE BUILDING, OR ANY FLAMMABLE GAS TO BE USED DURING CONSTRUCTION. 4. DUST CONTROL: DEBRIS, DIRT, AND DUST TO BE CLEANED UP AND CLEARED FROM THE BUILDING SITE DAILY TO AVOID EXCESSIVE ACCUMULATION. 5. PROTECTION A. CONTRACTOR TO PROVIDE ADJOINING PROPERTY PROTECTION IN ACCORDANCE WITH CODE REQUIREMENT (NJAC 5:23-2.15 (f)1.I(1) & 5:23-2.34). B. CONSTRUCTOR SHALL TAKE EVERY APPROPRIATE PRECAUTION IN ACCORDANCE WITH CURRENT BUILDING CODES AND CONSTRUCTION PRACTICES TO ENSURE ADJOINING PROPERTIES ARE PROTECTED FROM DAMAGE

.I(1) & 5:23-2.34). B. CONSTRUCTOR SHALL TAKE EVERY APPROPRIATE PRECAUTION IN ACCORDANCE WITH CURRENT BUILDING CODES AND CONSTRUCTION PRACTICES TO ENSURE ADJOINING PROPERTIES ARE PROTECTED FROM DAMAGE DURING DEMOLITION AND CONSTRUCTION. C. BEFORE COMMENCE ANY WORK THE CONSTRUCTOR SHALL NOTIFY THE NEIGHBOURS ON BOTH SIDES PRIOR TO COMMENCEMENT OF ANY WORK. 1123 BROADWAY, SUITE 302, NY, NY 10010 PHONE 646.248.6664 WWW.JMAPC.COM G. DRYWALL 1. EXPOSED GYPSUM BOARD: ASTMC36 A. TYPE X WHERE INDICATED AND WHERE REQUIRED FOR FIRE-RESISTANCE RATING INDICATED. B. LONG EDGES: STANDARD TAPER C. THICKNESS: 5/8", OR AS SHOWN ON DRAWINGS. 2. TRIM ACCESSORIES A. PROVIDE MANUFACTURER'S STANDARD METAL TRIM ACCESSORIES, OF THE BEADED TYPE WITH FACE FLANGES FOR CONCEALMENT IN JOINT COMPOUND EXCEPT WHERE SEMI-FINISHING OR EXPOSED TYPE LOCATIONS. B. CORNER BEADS AT EXTERNAL CORNERS C. EDGE TRIM OF THE SHAPE INDICATED WHERE EDGE OF GYPSUM BOARD WOULD OTHERWISE BE EXPOSED OR SEMI- EXPOSED: L-TYPE FOR TIGHT ABUTMENT AT EDGES, OTHERWISE U-TYPE AS NEEDED/ REQUIRED. D. CONTROL JOINT UNITS, OF METAL AT LOCATIONS RECOMMENDED BY THE MANUFACTURER. 3. CONCEALED ACOUSTICAL SEALANT: NON-SHRINKING, NON- DRYING, NON-MIGRATING, NON- STAINING, MASTIC. 4. EXPOSED ACOUSTICAL SEALANT: LATEX, ACRYLIC, OR ACRYLIC-LATEX TYPE, PERMANENTLY ELASTIC AND PAINTABLE. 5. JOINT TAPE: ASTM C475, PERFORATED 6. JOINT COMPOUND: ASTM C 475, OF THE TYPE INDICATED. PROVIDE READY-MIXED VINYL-TYPE FOR INTERIOR WORK. PROVIDE 2 SEPARATE GRADES OF COMPOUND: ONE SPECIFICALLY FOR BEDDING TAPE AND ONE FOR TOPPING. 7. INSTALLATION SHALL BE PERFORMED ONLY BY AN APPLICATOR EXPERIENCED IN USING THIS PRODUCT AND SHALL USE TOOLS AND EQUIPMENT APPROVED BY THE MANUFACTURER. 8. INSTALL GYPSUM BOARDS IN LENGTHS AND DIRECTIONS WHICH WILL MINIMIZE NUMBER OF END JOINTS, AND AVOID END JOINTS IN CENTRAL AREA OF CEILINGS. 9. INSTALL WALLS AND PARTITIONS WITH EXPOSED GYPSUM BOARDS VERTICAL, WITH JOINTS OFFSET ON OPPOSITE SIDES OF PARTITIONS. OTHERWISE, INSTALL BOARDS AT RIGHT-ANGLES WITH SUPPORTS, EXCEPT WHERE RECOMMENDED IN A DIFFERENT ARRANGEMENT BY MANUFACTURER. 10. FORM CONTROL JOINTS WITH 1/2" SPACE BETWEEN BOARDS. INSTALL ACOUSTICAL SEALANT AT BASE OF SPACE, AND APPLY TRIM ACCESSORY AT FACE. 11. ACOUSTICAL SEALANT: DEMISING WALLS TO BE "SOUND RETARDING" WITH AN STC RATING OF 45 MIN.: APPLY 2 SEPARATE BEADS OF ACOUSTICAL SEALANT ALL

ALANT AT BASE OF SPACE, AND APPLY TRIM ACCESSORY AT FACE. 11. ACOUSTICAL SEALANT: DEMISING WALLS TO BE "SOUND RETARDING" WITH AN STC RATING OF 45 MIN.: APPLY 2 SEPARATE BEADS OF ACOUSTICAL SEALANT ALL AROUND AT INTERRUPTIONS OF DRYWALL WORK AS RECOMMENDED BY THE MANUFACTURER. 12. FORM "FLOATING" CONSTRUCTION FOR GYPSUM BOARDS AT INTERNAL CORNERS, EXCEPT WHERE SPECIAL ISOLATION OF EDGE TRIM IS INDICATED. 13. ISOLATE DRYWALL WORK FROM ABUTTING STRUCTURAL AND MASONRY WORK; PROVIDE EDGE TRIM AND ACOUSTICAL SEALANT AS RECOMMENDED BY THE MANUFACTURER. 14. INSTALL WATER-RESISTANT BACKING BOARDS WHERE SHOWN TO RECEIVE TILE AND SIMILAR RIGID APPLIED FINISHES. DO NOT APPLY TAPE AND COMPOUND AT JOINTS. SEAL CUT EDGE, JOINTS AND PENETRATIONS WITH WATER-RESISTANT SEALANT PRIOR TO INSTALLATION. 15. SCREW GYPSUM BOARD TO SUPPORTS, JOINTS, STUDS, ETC. 16. EXCEPT AS OTHERWISE INDICATED, APPLY JOINT TAPE AND JOINT COMPOUND AT JOINTS (BOTH DIRECTIONS) BETWEEN GYPSUM BOARDS. APPLY COMPOUND AT ACCESSORY FLANGES, PENETRATIONS, FASTENER HEADS, AND SURFACE DEFECTS. 17. INSTALL COMPOUND IN 2 COATS (PLUS PREFILL OF CRACKS WHERE RECOMMENDED BY MANUFACTURER); SAND AFTER LAST COAT. 18. APPLY SINGLE COAT USG IMPERIAL FINISH PLASTER, OR APPROVED EQUIVALENT, SMOOTH- TROWEL FINISH. 19. GENERAL STANDARD: GYPSUM ASSOCIATION SPECIFICATION GA-216, AND MANUFACTURER'S INSTRUCTIONS (WHICHEVER IS MORE STRINGENT). 20. MATERIALS (USG OR APPROVED EQUAL) H. GUARANTEES: 1. MATERIALS: THE CONTRACTOR SHALL FURNISH TO THE OWNER A 5 YEAR WRITTEN GUARANTEE ON ALL MATERIALS FURNISHED BY THOSE TRADES AS LISTED IN THIS SECTION TO BE FREE FROM DEFECTS DUE TO FAULTY WORKMANSHIP AND / OR MATERIALS. ALL DEFECTIVE MATERIAL SHALL BE REPLACED AS REQUIRED IMMEDIATELY AFTER PROPER NOTICE, AT NO COST TO THE OWNER. PART 7-THERMAL AND MOISTURE PROTECTION A. GENERAL 1. SEE GENERAL CONDITIONS 2. SEE PART IV - MASONRY B. MATERIALS 1. ASPHALTIC BITUMINOUS TROWEL ON DAMPPROOFING FOR FOUNDATIONS AND BELOW GRADE MASONRY WALLS. 2. CAULKING AND SEALANTS SHALL BE SELECTED BY THE CONTRACTOR TO SUIT CONDITIONS AND MATERIALS. A. CAULKING AND SEALANTS TO MATCH SURROUNDING SURFACE COLORS. B. ALL MATERIALS SHALL BE CAREFULLY SELECTED FOR COMPATIBILITY WITH EACH OTHER IN EACH JOINT SYSTEM. C. ALL MATERIALS SHALL BE INSTALLED AS PER THE MANUFACTURERS WRITTEN INSTRUCTIONS. 3. INSULATION SHALL BE INSTALLED IN THE TYPES AND SHAPES AS SHOWN ON

PATIBILITY WITH EACH OTHER IN EACH JOINT SYSTEM. C. ALL MATERIALS SHALL BE INSTALLED AS PER THE MANUFACTURERS WRITTEN INSTRUCTIONS. 3. INSULATION SHALL BE INSTALLED IN THE TYPES AND SHAPES AS SHOWN ON THE DRAWINGS AND AS FOLLOWS: A. FIBERGLASS ROLLS OR BATTS FACED WITH ALUMINUM FOIL VAPOR RESISTANT MEMBRANE WITH INTEGRAL NAILING FLANGES. I. EXTERIOR WALLS: 3 1/2", R-13 MIN. WHERE SHOWN OR NOTED ONLY. II. PROVIDE UNFACED BATTS AT INTERIOR PARTITION WALLS AND CEILINGS IN THE SIZES AS SHOWN ON THE DRAWINGS WHERE SHOWN OR REQUIRED FOR SOUND ABSORPTION REQUIREMENTS. III. ROOFS AND CEILINGS UNDER UNHEATED SPACES: 9", R-30 B. RIGID INSULATION SHALL BE INSTALLED IN THE SIZES AS SHOWN ON THE DRAWINGS, SHALL BE EXTRUDED AND HAVE AN "R" VALUE OF 5 PER INCH. I. INSULATION SHALL BE "STYROFOAM" BRAND AS MANUFACTURED BY THE DOW CHEMICAL CO. OR EQUAL. 4. PROVIDE A TOTAL ROOF DRAINAGE SYSTEM AS SHOWN OR REQUIRED, INCLUDING, BUT NOT LIMITED TO GUTTERS, LEADERS, CHIPS, CLEATS, CAPS, ROOF DRAINS, ETC. A. PREFINISHED COLOR AS SELECTED, ALL MATERIALS SHALL MATCH. B. 0.04" ALUMINUM GUTTER, PROFILE AND SIZES AS SHOWN ON DRAWINGS. (EXPANSION JOINTS AS REQUIRED TO PREVENT BUCKLING) C. 0.04" ALUMINUM DOWNSPOUT, PROFILE AND SIZES AS REQUIRED, TIE TO UNDERGROUND DRAINAGE SYSTEM. D. ALUMINUM HANGERS FOR GUTTER AND STRAPS FOR DOWN SPOUTS, SIZES AS REQUIRED FOR JOB APPLICATION. E. ALL ACCESSORIES, MITERS, SLIP JOINTS, CONNECTIONS, END CAPS, ELBOWS, EXPANSION JOINTS, ETC. F. 0.20" FLASHING AND COUNTER FLASHING. G. SEALING OF ALL JOINTS AS PER MANUFACTURER'S RECOMMENDATIONS. 5. FLASHINGS SHALL BE INSTALLED WHERE NOTED OR REQUIRED. A. ALL FLASHINGS AND ACCESSORIES SHALL BE OF CORROSIVE RESISTANT MATERIALS. B. ALL MATERIALS SHALL BE FULLY COMPATIBLE WITH ONE ANOTHER AND ADJOINING MATERIALS. C. DISSIMILAR MATERIALS - ALUMINUM SHALL NOT BE CONCRETE, STUCCO MASONRY OR CORROSIVE NONMETALLIC MATERIALS WHICH MIGHT BECOME REPEATEDLY WET. WOOD TREATED WITH SOME CHEMICALS CAN CAUSE PROBLEMS WHEN WET, SO USE ONLY TREATMENTS SUCH AS CREOSOTE, ZINC NAPHTHANATE PENTACHOLOROPHENAL (5% CONCENTRATION) OR WOLMAN SALTS. DO NOT PERMIT WATER FROM COPPER FLASHING TO DRAIN OVER ALUMINUM PRODUCTS. 6. ROOFING SHALL BE INSTALLED IN THE LOCATIONS AS SHOWN ON THE DRAWINGS AND SHALL BE AS FOLLOWS: I. MODIFIED BITUMEN ROOF SEE MANUFACTURER'S RECOMMENDATIONS II. 15# ASPHALT SATURATED FELT UNDERLAYMENT. III. ALL ROOFING

E INSTALLED IN THE LOCATIONS AS SHOWN ON THE DRAWINGS AND SHALL BE AS FOLLOWS: I. MODIFIED BITUMEN ROOF SEE MANUFACTURER'S RECOMMENDATIONS II. 15# ASPHALT SATURATED FELT UNDERLAYMENT. III. ALL ROOFING MATERIALS SHALL BE MANUFACTURED AND SUPPLIED BY A SINGLE ROOFING MANUFACTURER: CERTAINTEED, GEORGIA-PACIFIC OR APPROVED EQUAL. VII. COLOR BY ARCHITECT / OWNER. C. SOLID WOOD SIDING HORIZONTAL SIDING PANELS SHALL HAVE 4" NOMINAL EXPOSURE WITH DOUBLE BEVEL. 1. SIDING TO HAVE FINISH AS SPECIFIED BY ARCHITECT/OWNER 2. WORKMANSHIP AND INSTALLATION I. BEFORE STARTING WORK, VERIFY GOVERNING DIMENSIONS OF BUILDING EXAMINE, CLEAN, REPAIR IF NECESSARY, ANY ADJOINING WORK ON WHICH THIS WORK IS IN ANY WAY DEPENDENT FOR ITSPROPER INSTALLATION. II. ALL WORK SHALL BE INSTALLED IN A COMPLETE PROFESSIONAL, WORKMANLIKE FASHION BY THOSE SKILLED IN THEIR TRADES AND IN STRICT ACCORDANCE WITH MANUFACTURERS WRITTEN INSTRUCTIONS. III. COMPLY WITH ALL APPLICABLE CODES, ORDINANCES, AND SAFE WORK PRACTICES. IV. ALL WORK EXPOSED TO VIEW SHALL BE INSTALLED TRUE TO LINE, AT PROPER ELEVATIONS, AND IN ALIGNMENT WITH OTHER WORK. V. INSTALL WOOD SIDING IN ACCORDANCE APPLICABLE CODES VI. UPON COMPLETION OF THIS WORK, ALL SIDING, ETC. SHALL BE CLEANED SO THAT NO SOILED AREAS, FINGERPRINTS, ETC. ARE VISIBLE TO THE NAKED EYE. ALL SCRAP SHALL BE REMOVED AND PROPERLY DISCARDED. D. GUARANTEES 1. MATERIALS: THE CONTRACTOR SHALL FURNISH TO THE OWNER A 15 YEAR WRITTEN GUARANTEE ON ALL MATERIALS FURNISHED BY THOSE TRADES AS LISTED IN THIS SECTION TO BE FREE FROM DEFECTS DUE TO FAULTY WORKMANSHIP AND / OR MATERIALS. ALL DEFECTIVE MATERIAL SHALL BE REPLACED AS REQUIRED IMMEDIATELY AFTER PROPER NOTICE, AT NO COST TO THE OWNER. 2. THE CONTRACTOR SHALL GUARANTEE ALL ROOFING, WATERPROOFING, FLASHINGS, ETC. TO BE FREE FROM LEAKS FOR A PERIOD OF NOT LESS THAN 20 YEARS FROM DATE OF FINAL ACCEPTANCE. PART 8 - OPENINGS (SEE WINDOW / DOOR SCHEDULES) PART 9 - FINISHES (WHERE APPLICABLE) A. GENERAL 1. SEE GENERAL CONDITIONS 2. THE CONTRACTOR SHALL PROVIDE ALL ITEMS, MATERIALS ETC. AS SHOWN OR NOTED ON THE DRAWINGS OR DESCRIBED HEREIN, INCLUDING LABOR, EQUIPMENT ANY OTHER ITEMS REQUIRED FOR THE COMPLETE INSTALLATION OF ALL FINISHES. A. THE OWNER SHALL BE RESPONSIBLE FOR FINAL SELECTION OF ALL FINISH MATERIALS AND COLORS. B. MATERIALS 1. RESILIENT FLOOR COVERINGS SHALL BE INSTALLED IN THE LOCATIONS AS SHOWN AND NOTED

ALL FINISHES. A. THE OWNER SHALL BE RESPONSIBLE FOR FINAL SELECTION OF ALL FINISH MATERIALS AND COLORS. B. MATERIALS 1. RESILIENT FLOOR COVERINGS SHALL BE INSTALLED IN THE LOCATIONS AS SHOWN AND NOTED ON THE DRAWINGS. A. RESILIENT FLOORING CONTRACTOR SHALL INSPECT ALL SUBFLOORING AND IMMEDIATELY REPORT FINDINGS TO THE OWNER. B. ALL FLOOR COVERINGS SHALL CONFORM TO ALL APPLICABLE FEDERAL SPECIFICATIONS. C. ALL MATERIALS SHALL BE NEW AND FREE FROM DEFECTS; BEST COMMERCIAL GRADE FOR EACH SPECIFIC FUNCTION AND SITUATION. D. ALL PRIMERS AND ADHESIVES SHALL BE COMPATIBLE WITH FLOOR FINISH AS RECOMMENDED BY THE MANUFACTURER. E. VINYL BASES SHALL BE THE COVE TYPE AND SHALL BE .085" X 4" MOLDED VINYL. 2. CERAMIC TILE (WHERE/ IF APPLICABLE ) A. INSTALL CERAMIC TILE WHERE SHOWN ON THE PLANS AND IN ACCORDANCE WITH ALL MANUFACTURES REQUIREMENTS AND ANSI STANDARDS. B. COLORS AND PATTERNS BY ARCHITECT/ OWNER. C. CERAMIC TILES SHALL BE IN THE SHAPES AND SIZES AS SPECIFIED IN ELEVATIONS I. FURNISH COMBINATION COVE AND BASE COMPLETE WITH COMBINATION ANGLES AND STRETCHER SHAPES FOR INTERNAL AND EXTERNAL CORNERS AND ANY OTHER SHAPES AND ACCESSORIES AS REQUIRED FOR THE COMPLETE INSTALLATION OF CERAMIC TILE. 3. PAINTING ALL SURFACES TO BE PAINTED SHALL BE CLEAN, PROPERLY PREPARED IN ACCORDANCE WITH PAINT MANUFACTURES PRINTED INSTRUCTIONS. PROTECT ADJACENT SURFACES AS NECESSARY. CLEAN ALL DRIPS AND SPATTERS. COLOR AND GLOSS OF INTERIOR SPACES SHALL BE SELECTED BY THE OWNER. EXTERIOR PAINT COLORS SELECTED BY OWNER AND APPROVED BY ARCHITECT. THE PAINTING AND FINISHING OF ALL INTERIOR AND EXTERIOR ITEMS AND SURFACES SHALL BE AS FOLLOWS: A. EXTERIOR WOOD AND TRIM SHALL RECEIVE 1 COAT OF PRIMER AND 2 FINISH COATS OF ALKYD OIL ENAMEL. B. EXTERIOR AND INTERIOR FERROUS METAL SHALL BE PROPERLY PRIMED AND GIVEN 2 COATS OF ALKYD ENAMEL. C. INTERIOR GYPSUM DRYWALL SHALL BE PROPERLY PRIMED AND GIVEN 1 COAT LATEX - SEE FINISH SCHEDULE. D. INTERIOR WOOD WORK, DOORS AND TRIM SHALL BE GIVEN 1 COAT SEMI-TRANSPARENT ALKYD- OIL STAIN AND 1 COAT POLYURETHANE BOTH SIDES, TOP AND BOTTOM. E. INTERIOR EXPOSED CONCRETE FLOORS SHALL BE GIVEN 1 COAT OF CLEAR CONCRETE SEALER-DUST PROOFING. F. EXTERIOR STUCCO AND MASONRY SHALL BE GIVEN 2 COATS OF OIL BASED ENAMEL. G. PAINTS SHALL BE MANUFACTURED BY ONE OF THE FOLLOWING: BENJAMIN MOORE PAINTS CON- LUX PAINT CO. OR EQUAL C. INSTALLATION 1. ALL MATERIALS IN THIS

MASONRY SHALL BE GIVEN 2 COATS OF OIL BASED ENAMEL. G. PAINTS SHALL BE MANUFACTURED BY ONE OF THE FOLLOWING: BENJAMIN MOORE PAINTS CON- LUX PAINT CO. OR EQUAL C. INSTALLATION 1. ALL MATERIALS IN THIS SECTION SHALL BE INSTALLED IN THE MOST PROFESSIONAL AND WORKMANLIKE MANNER, IN STRICT ACCORDANCE WITH THE MANUFACTURERS WRITTEN INSTRUCTION AND ALL APPLICABLE CODES AND STANDARDS. 2. INSTALL ALL ACCESSORIES, TRIM PIECES, ETC. AS REQUIRED FOR THE COMPLETE INSTALLATION OF EACH FINISH MATERIAL. 3. ALL MATERIALS SHALL BE ACCURATELY SCRIBED TO FIT PIPES, COLUMNS, AND ALL OTHER FEATURES AND SHALL BE NEATLY CUT AND BUTTED TO ALL WALLS BASES, ETC. 4. CERAMIC TILES SHALL BE SET PLUMB LEVEL AND TRUE TO LINE, ALL JOINTS SHALL BE UNIFORM; 1/4" RUN THRU FROM FLOORS TO WALL AND FROM WALL TO WALL. A. ALL TILE SHALL BE SET IN ACCORDANCE WITH THE TILE COUNCIL OF AMERICA STANDARDS AND WITH AN EPOXY ADHESIVE EXCEPT AT EXTERIOR AND WET APPLICATIONS WHERE TILE SHALL BE DRY SET MORTAR. B. GROUT SHALL BE PORTLAND CEMENT COMMERCIAL GRADE, COLOR SHALL BE WHITE AT ALL FLOORS AND WALLS. 5. PAINTING SHALL BE DONE BY THOSE SKILLED IN THEIR TRADE. APPLY ALL MATERIAL EVENLY. NO SAGS, RUNS, CRAWLS, OR OTHER DEFECTS SHALL BE ALLOWED. A. ALL SURFACES TO BE PAINTED SHALL BE THOROUGHLY AND UNIFORMLY COVERED, APPLY NECESSARY COATS TO COMPLETE JOB. D. PROTECTION AND CLEANING 1. ALL WORK SHALL BE PROTECTED BY A TEAR RESISTANT HEAVY WEIGHT KRAFT PAPER, TAPE ALL SEAMS. PAPER SHALL BE INSTALLED IN AREAS SUBJECT TO TRAFFIC WHICH WOULD BE DETRIMENTAL TO THE FINISHED SURFACE. ALL COVERINGS SHALL REMAIN IN PLACE FOR THE DURATION UNTIL THE BUILDING IS READY FOR OCCUPANCY. 2. EACH TRADE SHALL THOROUGHLY CLEAN AND MAKE GOOD ALL WORK IN THEIR CONTRACT. REMOVE ALL TRACES OF GROUT, DIRT, GREASE, ETC. TO THE SATISFACTION OF THE OWNER. E. GUARANTEES 1. MANUFACTURERS AND CONTRACTORS SHALL GUARANTEE ALL WORK FOR A PERIOD OF 2 YEARS FROM DATE OF FINAL ACCEPTANCE. ALL WORKMANSHIP AND MATERIALS SHALL BE FREE FROM DEFECTS. ALL REPAIRS SHALL BE PROMPTLY MADE. 2. CONTRACTORS SHALL PROVIDE OWNER WITH SURPLUS STOCK OF ALL FINISH PRODUCTS. 3. IN THE EVENT ANY ADJACENT AREAS DAMAGED AS THE RESULT OF THE FAILED PRODUCT THE DAMAGED WORK SHALL BE REPAIRED AT NO COST TO THE OWNER. INCLUDED ALSO SHALL BE ADJACENT AREAS WHICH MUST BE DISTURBED IN ORDER TO REPAIR DEFECTIVE MATERIALS. PART 10 - SPECIALTIES (NOT USED) PART 11 -