V4 06 Response to Board Engineers Review 2 1 26 2023

PR4 ALUMINUM POLE currentlighting.com/aal © 2022 HLI Solutions, Inc. All rights reserved. Information and specifications subject to change without notice. All values are design or typical values when measured under laboratory conditions.Page 1 of 2 Rev 06/29/22 aal_pr4_spec_R01 AAL Poles CONSTRUCTION • Base casting shall be heat treated to a T-6 condition, and of uniform wall thickness, with no warping or mold shifting. WARNINGS • Caution must be exercised in the selection of a design wind speed when the pole is to be installed in a special wind region (as indicated by the wind map) or in an area where wind speed is unpredictable. • AAL recommends consulting a local engineer when the pole is to be installed in an area that may be subject to extreme weather and exposure. • Poles installed on structures such as buildings and bridges may be subjected to vibration, oscillations, and other fatigue effects which are not covered by the AAL warranty. • The use of banners or other appendages can severely affect the loading of a pole. No banner or other appendage should be attached to an AAL pole unless approved by AAL. • If the products are to be used on an existing foundation or on other structures, the customer assumes all responsibility for the structural integrity of the existing foundation, anchorage or structures and all the consequences arising therefrom. SPECIFICATIONS DATE: LOCATION: TYPE: PROJECT: CATALOG #: YPE X IMUM ALLOWABLE EPA (MPH) 85 90 100 110 120 130 140 150 12.3 10.9 8.7 7 5.7 4.8 4.1 3.6 9.1 8 6.3 4.9 4.0 3.3 2.8 2.4 6.9 6 4.5 3.4 2.6 2.1 1.8 1.5 5.2 4.4 3.2 2.3 1.5 1.2 1 0.8 3.9 3.2 2.1 1.3 0.8 0.5 0.4 0.2 21.5 19.2 15.5 12.7 10.6 9.0 7.7 6.7 16.5 14.6 11.7 9.4 7.8 6.6 5.6 4.8 13.0 11.4 9 7.2 5.8 4.9 4.1 3.5 10.3 9.1 7 5.4 4.3 3.6 3 2.5 8.3 7.2 5.4 4.1 3.1 2.5 2.1 1.8 6.6 5.6 4.1 2.9 2.1 1.6 1.3 1 5.1 4.3 3.0 1.9 1.2 0.9 0.6 0.4 YPE SPECIFICATIONS Base shall be cast aluminum #356 alloy, free of any porosity, foreign materials, or cosmetic fillers. Base casting shall be heat treated to a T-6 condition, and of uniform wall thickness, with no warping or mold shifting. WARNINGS Caution must be exercised in the selection of a design wind speed when the pole is to be installed in a special wind region (as indicated by the wind map) or in an area where wind speed is unpredictable. AAL recommends consulting a local engineer when the pole is to be

n the pole is to be installed in a special wind region (as indicated by the wind map) or in an area where wind speed is unpredictable. AAL recommends consulting a local engineer when the pole is to be installed in an area that may be subject to extreme weather and exposure Poles installed on structures such as buildings and bridges may be subjected to vibration, oscillations, and other fatigue effects which are not covered by the AAL warranty. The use of banners or other appendages can severely affect the loading of a pole. No banner or other appendage should be attached to an AAL pole unless approved by AAL. If the products are to be used on an existing foundation or on other structures, the customer assumes all responsibility for the structural integrity of the existing foundation, anchorage or structures and all the consequences arising therefrom. CAUTION Poles should never be erected without the luminaire installed. Warranty is voided if the pole is erected without the luminaire. The warranty is PR4 AXIMUM ALLOWABLE EPA (MPH) 85 90 100 110 120 130 140 150 12.3 10.9 8.7 7 5.7 4.8 4.1 3.6 9.1 8 6.3 4.9 4.0 3.3 2.8 2.4 6.9 6 4.5 3.4 2.6 2.1 1.8 1.5 5.2 4.4 3.2 2.3 1.5 1.2 1 0.8 3.9 3.2 2.1 1.3 0.8 0.5 0.4 0.2 21.5 19.2 15.5 12.7 10.6 9.0 7.7 6.7 16.5 14.6 11.7 9.4 7.8 6.6 5.6 4.8 13.0 11.4 9 7.2 5.8 4.9 4.1 3.5 10.3 9.1 7 5.4 4.3 3.6 3 2.5 8.3 7.2 5.4 4.1 3.1 2.5 2.1 1.8 6.6 5.6 4.1 2.9 2.1 1.6 1.3 1 5.1 4.3 3.0 1.9 1.2 0.9 0.6 0.4 4. COLOR Base casting shall be heat treated to a T-6 condition, and of uniform wall thickness, with no warping or mold shifting. WARNINGS Caution must be exercised in the selection of a design wind speed when the pole is to be installed in a special wind region (as indicated by the wind map) or in an area where wind speed is unpredictable. AAL recommends consulting a local engineer when the pole is to be installed in an area that may be subject to extreme weather and exposure. Poles installed on structures such as buildings and bridges may be subjected to vibration, oscillations, and other fatigue effects which are not covered by the AAL warranty. The use of banners or other appendages can severely affect the loading of a pole. No banner or other appendage should be attached to an AAL pole unless approved by AAL. If the products are to be used on an existing foundation or on other structures, the customer assumes all

a pole. No banner or other appendage should be attached to an AAL pole unless approved by AAL. If the products are to be used on an existing foundation or on other structures, the customer assumes all responsibility for the structural integrity of the existing foundation, anchorage or structures and all the consequences arising therefrom. CAUTION Poles should never be erected without the luminaire installed. Receptacle Base Finish Mounting 4 5 6 7 SH ARD COLOR Antique Green Black Matte Black Corten Dark Bronze Dark Green Light Grey Matte Aluminum Medium Grey White Titanium CAUTION • Poles should never be erected without the luminaire installed. • Anchor bolts shall be hot dip galvanized steel. Eight galvanized hex nuts and flat washers, and a bolt circle template shall be provided. Anchor bolt for poles are 3/4” x 24” x 3”. CERTIFICATION • Certified UL 1598 in accordance with Article410 of ANSI/NFPA 70, National Electrical Code. ORDERING GUIDE Example: PR4-4R12-125-PCR-GFI-SBC-PTF-BLT CATALOG # POLE Series Shaft Options Control Receptacle Base Finish PR4 4" Round Pole 4R8-125 4R8-125 4R10-125 4R10-125 4R12-125 4R12-125 4R14-125 4R14-125 4R16-125 4R16-125 4R8-226 4R8-226 4R10-226 4R10-226 4R12-226 4R12-226 4R14-226 4R14-226 4R16-226 4R16-226 4R18-226 4R18-226 4R20-226 4R20-226 LR Ladder Rest PCR Photocontrol Receptacle PHC-120V Button Type Photocell, 120V PHC-208V Button Type Photocell, 208V PHC-240V Button Type Photocell, 240V PHC-277V Button Type Photocell, 277V SCP Sensor Control Programmable 120-277V SCP-347V Sensor Control Programmable 347V SCP-480V Sensor Control Programmable 480V GFI GFCI Receptacle DRB Duplex Receptacle RBC Receptacle Box Cover SBC 1-piece Cover 2PCBC 2-piece Cover BC1 12.75"Ø x 8.25"H 1pc. Cover BC2 12.75"Ø x 16.25"H 3pc. Cover BC5 14"Ø x 24"H 2pc. Cast Cover BC6 17"Ø x 13"H 2pc. Cast Cover BC7 18"Ø x 30"H 3pc. Cast Cover BC8 12"Ø x 36"H 2pc. Cast Cover ACBCR 14"Ø x 18" Arts & Crafts® Round 3pc. Cast Cover HB Hinged Base BLS Black Gloss Smooth BLT Black Matte Textured DBS Dark Bronze Gloss Smooth DBT Dark Bronze Matte Textured GTT Graphite Matte Textured LGS Light Grey Gloss Smooth LGT Light Grey Matte Textured PSS Platinum Silver Gloss Smooth VGT Verde Green Matte Textured WHS White Gloss Smooth WHT White Matte Textured Color Option CC 1 Custom Color Mounting TEN Tenon, 2 3/8" Ø x 4"H TEN3 Tenon, 3" Ø x 3"H 1A Single Side Arm 2B

oss Smooth VGT Verde Green Matte Textured WHS White Gloss Smooth WHT White Matte Textured Color Option CC 1 Custom Color Mounting TEN Tenon, 2 3/8" Ø x 4"H TEN3 Tenon, 3" Ø x 3"H 1A Single Side Arm 2B Double Side Arm PTF Post Top Fixture PTA Post Top Arm PTAD Post Top Adaptor ND No Drilling Maximum Allowable EPA (MPH) Series SHAFT OAH SHAFT WT 85 90 100 110 120 130 140 150 PR4 4R8-125 8' (2.4m) 4" RD x .125" 22 12.3 10.9 8.7 7.0 5.7 4.8 4.1 3.6 PR4 4R10-125 10' (3.1m) 4" RD x .125" 25 9.1 8.0 6.3 4.9 4.0 3.3 2.8 2.4 PR4 4R12-125 12' (3.7m) 4" RD x .125" 28 6.9 6.0 4.5 3.4 2.6 2.1 1.8 1.5 PR4 4R14-125 14' (4.3m) 4" RD x .125" 32 5.2 4.4 3.2 2.3 1.5 1.2 1.0 0.8 PR4 4R16-125 16' (4.9m) 4" RD x .125" 35 3.9 3.2 2.1 1.3 0.8 0.5 0.4 0.2 PR4 4R8-226 8' (2.4m) 4" RD x .226" 32 21.5 19.2 15.5 12.7 10.6 9.0 7.7 6.7 PR4 4R10-226 10' (3.1m) 4" RD x .226" 38 16.5 14.6 11.7 9.4 7.8 6.6 5.6 4.8 PR4 4R12-226 12' (3.7m) 4" RD x .226" 44 13.0 11.4 9.0 7.2 5.8 4.9 4.1 3.5 PR4 4R14-226 14' (4.3m) 4" RD x .226" 51 10.3 9.1 7.0 5.4 4.3 3.6 3.0 2.5 PR4 4R16-226 16' (4.9m) 4" RD x .226" 57 8.3 7.2 5.4 4.1 3.1 2.5 2.1 1.8 PR4 4R18-226 18' (5.5m) 4" RD x .226" 63 6.6 5.6 4.1 2.9 2.1 1.6 1.3 1.0 PR4 4R20-226 20' (6.2m) 4" RD x .226" 70 5.1 4.3 3.0 1.9 1.2 0.9 0.6 0.4 Notes: 1 Consult factory for custom color, marine and corrosive finish