24 010_ISSUED FOR ZONING

REVISIONS: # DESCRIPTION: DATE: ISSUED FOR PERMITS 4/10/2024 NOTE: THIS DRAWING IS APPROVED ONLY FOR THE SCOPE OF WORK INDICATED ON THE DRAWINGS. ALL OTHER MATTERS SHOWN ARE NOT TO BE RELIED UPON OR CONSIDERED AS EITHER BEING APPROVED BY THIS ARCHITECT AND HIS CONSULTANTS OR IN ACCORDANCE WITH APPLICABLE CODES AND STANDARDS OBSTRUCTED HIGH SIDE REACH 48" MIN. 10" MAX 48" MIN 36" MIN 9" MIN ELEVATION SWING DOOR 2B 5A SCALE: 1/2" = 1'-0" SIDE REACH CLEARANCES UNOBSTRUCTED SIDE REACHOBSTRUCTED HIGH FORWARD REACH UNOBSTRUCTED FORWARD REACH SEGMENT LENGTH LESS THAN OR EQUAL TO 24" GREATER THAN 24" MINIMUM SEGMENT WIDTH 32" (SEE NOTE) 36" NOTE: CONSECUTIVE SEGMENTS OF 32" WIDE MUST BE SEPARATED BY A ROUTE SEGMENT 48" LONG MINIMUM AND 36" WIDE MINIMUM. 4'-0" MIN. 2'-6" 5'-0" 5'-0" 4'-0" INTERIOR: 2 1/2" MIN. SIZE EXTERIOR: 8" MIN. SIZET-SHAPED PLAN CIRCULAR PLAN 5'-0" 5'-0" 3'-0" 2'-0" 12"12" FRONT APPROACH PULL SIDE 60" MIN. 60" MIN. DOOR WIDTH DOOR WIDTH DOOR WIDTH 48" MIN. 60" MIN. 18"MIN 25"MAX.17"-25" 2'-6" MIN. 2'-6" MIN. 15" MIN 48" MAX 48" MAX 44" MAX 20" MAX >20"-25" MAX 15" MIN 48" MAX 48" MAX 48" MAX 34" MAX 34" MAX 10" MAX > 10"-24" MAX 36" MIN 36" MIN 32" MIN 32" MIN 24" MAX24" MAX PARALLEL APPROACH 60" MIN FORWARD APPROACH 6" MAX PLAN 9" MIN 27" MIN 8" MIN 11" MIN ELEVATION PLAN 5'-0" MIN. 36" MIN. 5'-0" MIN. APPROACH FRONT APPROACH PUSH SIDE APPROACH HINGE APPROACH PULL SIDE 24" MIN. 48" MIN. LATCH APPROACH PULL SIDE 54" MIN. W/ CLOSER PROVIDE THIS SPACE IF DOOR IS EQUIPPED WITH BOTH A LATCH AND A CLOSER. 48" MIN. 12" MIN. 12" MIN. 22" MIN. PROVIDE THIS SPACE IF DOOR IS EQUIPPED WITH A CLOSER. HINGE APPROACH PUSH SIDE LATCH APPROACH PUSH SIDE 42" MIN 24" MIN. 42" MIN 48" MIN. PROVIDE THIS SPACE IF DOOR IS EQUIPPED WITH A CLOSER. W/ LATCH & CLOSER WITH CLOSER ALTERNATE 42" MIN ALTERNATE 42" MIN 90° FOLDING DOOR SLIDING DOOR 32" MIN 32" MIN 32" MIN APPROACH APPROACH APPROACH APPROACH X > 15" X > 24" 18" MIN6" MIN 6" MIN 12" MIN 6 0 " D I A C L E A R 1A SCALE: 1/2" = 1'-0" 180°/360° TURNING SPACE 1B SCALE: 1/2" = 1'-0" ALTERNATE TURNING SPACE 2A SCALE: 1/2" = 1'-0" CLEAR FLOOR SPACE SCALE: 1/2" = 1'-0" ALCOVE MANEUVERING CLEARANCES 3 SCALE: 1/2" = 1'-0" INTERNATIONAL SYMBOL 4 SCALE: 1/2" = 1'-0" CLEAR WIDTH OF ACCESSIBLE ROUTE SCALE: 1/2" = 1'-0" FORWARD REACH CLEARANCES 5C5B SCALE: 1/2" = 1'-0" TOE CLEARANCES SCALE: 1/2" = 1'-0" KNEE CLEARANCES 5D 6A

NTERNATIONAL SYMBOL 4 SCALE: 1/2" = 1'-0" CLEAR WIDTH OF ACCESSIBLE ROUTE SCALE: 1/2" = 1'-0" FORWARD REACH CLEARANCES 5C5B SCALE: 1/2" = 1'-0" TOE CLEARANCES SCALE: 1/2" = 1'-0" KNEE CLEARANCES 5D 6A SCALE: 1/2" = 1'-0" MANEUVERING CLEARANCE AT MANUAL SWINGING DOORS- PULL SIDE 6A SCALE: 1/2" = 1'-0" MANEUVERING CLEARANCE AT MANUAL SWINGING DOORS- PUSH SIDE 8 SCALE: 1/2" = 1'-0" DOORS IN A SERIES MANEUVERING CLEARANCES 9 SCALE: 1/2" = 1'-0" CLEAR WIDTHS- DOORS ACCESSIBILITY REQUIREMENTS DRAWING TITLE: JASON PEIST, AIA - ARCHITECT CHANGE OF USE- ADD A LEVEL 172-174 MAIN ST WEST ORANGE, NJ 07052 BLOCK 89, LOT 6 ESSEX COUNTY ARCHITECTURAL LICENSE #: NJ# 21AI02035200 NY# 039598 PA# RA410300 CT# ARI.0015695 RI# ARC.0005736 drawings, specifications & other documents, both paper copies and in electronic form, prepared by jason peist and consultants are instruments of service for use solely for this project. they may not be used for any purposes beyond the scope of this contract without written permission from jason peist. unlawful use of instruments of service shall be prosecuted to the full extent of the law. © COPYRIGHT 2024 JASON PEIST ARCHITECT, LLC 171 BROAD ST. MATAWAN, NJ 07747 732-379-0743 | info@jasonpeist.com 4/10/24 DATE: JOB NUMBER: SCALE: AS NOTED DRAWN BY: J.R.P. DRAWING NUMBER A-001 OF 24-010 173 SHEET: