JMA02P00301 262 270 MAIN STREET

SDR-35 PIPE. BELL END CUT AND CULTEC RECHARGER 180HD CHAMBER STORAGE = 3.445 FT3 / FT (0.32 m3 / m) INSERTED 6.0" [150mm] INTO CHAMBER FIGURE 1 INSTALLED LENGTH ADJUSTMENT = 1.0' [306 mm] INLET/OUTLET PIPE PER ENGINEER DESIGN. MAX. PIPE SIDE PORTAL ACCEPTS CULTEC HVLV FC-24 FEED CONNECTOR. PIPE TO BE INSERTED 12.0" [305mm] MIN. INTO CHAMBER

MAXIMUM PIPE SIZE: 12" [300mm] PVC 15" [375mm] HDPE 15" [375mm] PVC

15" [375mm] PVC WEST ORANGE ZOOM OF SIDE PORTAL SHOWING MAX. PIPE O.D. CULTEC HVLV FC-24 CULTEC RECHARGER 180HD HEAVY DUTY THREE VIEW FEED CONNECTOR THREE VIEW OPTIONAL CULTEC INSPECTION PORT - ZOOM DETAIL CULTEC SEPARATOR ROW - CULTEC INSPECTION PORT DETAIL (IF APPLICABLE)

SEPARATOR ROW - CULTEC INSPECTION PORT DETAIL (IF APPLICABLE) DRAWN BY : DESIGN BY : CHECKED BY : SCALE : HP HP JC AS NOTED SHEET #: 1 CULTEC R-180HD RECHARGER DETAILS

SHEET #: 1 CULTEC R-180HD RECHARGER DETAILS DATE : 05/15/2025 C1.14

C1.14 BINDING ORDER: JOB No. : C1.14 SCALE: N.T.S JMA02P003.01 14 of 15

NOTES: NOTES: H 1. INLETS MAY BE CONSTRUCTED OF BRICK, CONCRETE OR CONCRETE BLOCK. IF BRICK OR CONCRETE BLOCK IS USED, THE BOTTOM SHALL 1. INLETS MAY BE CONSTRUCTED OF BRICK, CONCRETE OR CONCRETE U HE BE SHOWN FOR CONCRETE AND THE OUTSIDE OF THE WALL SHALL BLOCK. IF BRICK OR CONCRETE BLOCK IS USED, THE BOTTOM SHALL BE SHOWN FOR CONCRETE AND THE OUTSIDE OF THE WALL SHALL BE PLASTERED WITH 21"

BE SHOWN FOR CONCRETE AND THE OUTSIDE OF THE WALL SHALL BE PLASTERED WITH 21" COAT BE DISHED AND SLOOF 1:2 CEMENT SAND MORTAR. 2. INVERTERS TO BE ELIMINATED IN BOTTOM OF TERMINAL INLETS. BE PLASTERED WITH 21" COAT BE DISHED AND SLOOF 1:2 CEMENT SAND MORTAR. D 2. INVERTERS TO BE ELIMINATED IN BOTTOM OF TERMINAL INLETS. A BOTTOM SHALL BE DISHED AND SLOPED TOWARDS THE OUTLET AT S A

A THE RATE OF 2" PER FOOT. THIS INLET MAY BE CONSTRUCTED OF BOTTOM SHALL BE DISHED AND SLOPED TOWARDS THE OUTLET AT BRICK, CONCRETE OR CONCRETE BLOCK. IF BRICK OR CONCRETE THE RATE OF 2" PER FOOT. THIS INLET MAY BE CONSTRUCTED OF BLOCK IS USED, THE BOTTOM SHALL BE AS SHOWN FOR CONCRETE AND THE OUTSIDE OF THE WALLS SHALL BE PLASTERED WITH 1/2" BRICK, CONCRETE OR CONCRETE BLOCK. IF BRICK OR CONCRETE BLOCK IS USED, THE BOTTOM SHALL BE AS SHOWN FOR CONCRETE AND THE OUTSIDE OF THE WALLS SHALL BE PLASTERED WITH 1/2" O COAT, BE DISHED AND SLOOF 1:2 CEMENT SAND

O COAT, BE DISHED AND SLOOF 1:2 CEMENT SAND MORTAR. 3. FOUNDATION AND INVERT TO BE CONSTRUCTED IN 2 STAGES. TOP SURFACE OF STAGE 1 TO BE LEFT ROUGH. COAT, BE DISHED AND SLOOF 1:2 CEMENT SAND MORTAR. 3. FOUNDATION AND INVERT TO BE CONSTRUCTED IN 2 STAGES. TOP ENGINEERING 4. PLACE INLET FOUNDATION WHICH ARE PRECAST ON A 6 INCH THICK SURFACE OF STAGE 1 TO BE LEFT ROUGH. BED OF COMPACTED COARSE AGGREGATE #57. EXTEND THE COARSE 4. PLACE INLET FOUNDATION WHICH ARE PRECAST ON A 6 INCH THICK BED OF COMPACTED COARSE AGGREGATE #57. EXTEND THE COARSE HUDSON ENGINEERING, LLC