13026 Resubmission

ACTOR TO CONSULT WITH STRUCTURAL ENGINEER 6. FOUNDATIONS ARE DESIGNED TO BEAR ON RESIDUAL SOIL OR ENGINEERED COMPACTED FILL F. FABRICATION SELECTED BY OWNER. HARDWARE STANDARDS SHALL COMPLY WITH ANSI A156.9 BEFORE REMOVING STRUCTURAL ELEMENTS. WITH AN ALLOWABLE BEARING PRESSURE OF 3,000 PSF. VERIFY SOIL CAPACITY AT TIME OF 1. COMPLY WITH ASIC "SPECIFICATIONS" AND APPROVED FINALIZED SHOP DRAWINGS. MARK AND 4. INSTALLATION 3. MAKE ALL WORK SAFE AS PER RULES AND REGULATIONS OF AUTHORITIES HAVING JURISDICTION EXCAVATION. MATCH-MARK UNITS FOR FIELD ASSEMBLY. A. INSTALL THE WORK PLUMB, LEVEL, TRUE AND STRAIGHT, WITH NO DISTORTIONS. SHIM AS OVER UTILITIES AND INSURE CONTINUED OPERATION AND PROTECTION OF EXISTING PIPES, LINES, 2. USE HIGH-STRENGTH BOLTS FOR FIELD CONNECTIONS, EXCEPT AS OTHERWISE INDICATED. REQUIRED USING CONCEALED SHIMS. INSTALL TO A TOLERANCE OF 1/8" IN 8'-0" FOR PLUMB AND DUCTS EQUIPMENT, ETC. 3. COMPLY WITH AWS CODE FOR PROCEDURES, APPEARANCE, AND QUALITY OF WELDS. LEVEL AND WITH 1/16" MAX. OFFSET IN FLUSH ADJOINING SURFACES. SHEET NUMBER 4. ALL REMOVALS AND SALVAGE, UNLESS SPECIFICALLY NOTED OR REQUESTED BY THE OWNER 4. USE MATERIALS OF SIZE AND THICKNESS SHOWN OR, IF NOT SHOWN, OF REQUIRED SIZE AND B. SCRIBE AND CUT WORK TO FIT ADJOINING WORK, AND REFINISH CUT SURFACES OR REPAIR SHALL BECOME THE PROPERTY OF THE CONTRACTOR. THICKNESS TO PRODUCE STRENGTH AND DURABILITY IN FINISHED PRODUCT. SHOP-PAINT ALL ITEMS

THICKNESS TO PRODUCE STRENGTH AND DURABILITY IN FINISHED PRODUCT. SHOP-PAINT ALL ITEMS DAMAGED FINISH AT CUTS. 5. TAKE FULL PRECAUTION TO PROTECT WORKMEN, PASSERBY, OR ANY OTHER PERSONS FROM NOT SPECIFIED TO BE GALVANIZED AFTER FABRICATION. C. ANCHOR WOODWORK TO ANCHORS OR BLOCKING BUILT-IN OR DIRECTLY ATTACHED TO FALLING DEBRIS AND OTHER HAZARDS. TAKE EVERY APPROPRIATE PRECAUTION IN ACCORDANCE 5. WELD CORNERS AND SEAMS CONTINUOUSLY: GRIND EXPOSED WELDS SMOOTH AND FLUSH. SUBSTRATES. SECURE TO GROUNDS, STRIPPING AND BLOCKING WITH COUNTERSUNK, WITH CURRENT BUILDING CODES, CONSTRUCTION PRACTICE AND THE SECRETARY OF THE INTERIOR ’ 6. FORM EXPOSED CONNECTIONS WITH HAIRLINE, FLUSH JOINTS: USE CONCEALED FASTENERS CONCEALED FASTENERS AND BLIND NAILS AS REQUIRED FOR A COMPLETE INSTALLATION. DOB APPROVAL STAMP: S STANDARDS AND GUIDELINES FOR THE TREATMENT OF HISTORIC PROPERTIES TO ENSURE THAT WHERE POSSIBLE. 5. PROTECTION PROXIMATE AND APPROXIMATE HISTORIC RESOURCES ARE PROTECTED FROM DAMAGE DURING A. COVER CASEWORK WITH 4-MIL POLYETHYLENE FILM, FOR PROTECTION AGAINST SOILING AND DEMOLITION. G. PROVISIONS FOR OTHER WORK: FABRICATES STRUCTURAL STEEL MEMBERS TO PROVIDE HOLES DETERIORATION DURING REMAINDER OF CONSTRUCTION PERIOD. 6. REMOVE

G. PROVISIONS FOR OTHER WORK: FABRICATES STRUCTURAL STEEL MEMBERS TO PROVIDE HOLES DETERIORATION DURING REMAINDER OF CONSTRUCTION PERIOD. 6. REMOVE ONLY NON-LOAD BEARING CONSTRUCTION AND PARTITIONS, CONTRACTOR TO VERIFY, FOR SECURING OTHER WORK AND FOR PASSAGE OF OTHER WORK THROUGH STEEL FRAMING AS PRIOR TO REMOVAL, THAT NO STRUCTURAL COMPONENTS, I.E. BEARING WALLS, BEAMS, HEADERS, REQUIRED COORDINATING WITH ALL MECHANICAL TRADES. F. WORKMANSHIP ETC.. SUPPORTING FLOOR, ROOF OR CEILING JOISTS ARE DESIGNATED FOR REMOVAL. CONTACT THE 1. STRUCTURAL AND MISCELLANEOUS STEEL: PAINT STRUCTURAL STEEL WORK, EXCEPT MEMBERS 1. ALL MANUFACTURE'S ASSOCIATIONS SPECIFICATIONS SHALL APPLY FOR FRAMING, CABINETRY, ARCHITECT PRIOR TO REMOVAL OF ANY CONSTRUCTION IN QUESTION OR DEVIATING FROM THE OR PORTIONS OF MEMBERS EMBEDDED IN CONCRETE OR MORTAR, AND CONTACT AREA TO BE STAIRS, ETC. DESIGN INTENT. CONTRACTOR'S NON-CONTACT OF ARCHITECT PRIOR TO REMOVAL OF ANY WORK WELDED OR RIVETED. CLEAN STEEL FRAME OF LOOSE MILL SCALE, RUST, OIL AND GREASE. APPLY 2. ALL WOODWORK SHALL BE FINISHED SMOOTH, HAND SANDED ON ALL EXPOSED SURFACES, FREE INDICATES HIS COMPLETE UNDERSTANDING THAT NO LOAD BEARING OR STRUCTURAL WORK IS PRIME PAINT TO PROVIDE A MINIMUM DRY FILM THICKNESS OF 2.0 MILS. FROM DEFECTS, DIRT, STAINS, ETC. BEING ALTERED UNDER THIS CONTRACT. 2. TOUCH-UP SHOP PAINT AFTER INSTALLATION. CLEAN FIELD WELDS, BOLTED CONNECTIONS AND 3. ALL

2. TOUCH-UP SHOP PAINT AFTER INSTALLATION. CLEAN FIELD WELDS, BOLTED CONNECTIONS AND 3. ALL WOODWORK SHALL BE ERECTED IN A THOROUGHLY WORKMANLIKE MANNER. 7. DEMOLITION AND REMOVAL OF EXISTING BUILDINGS, UTILITIES AND ANY SURROUNDING ABRADED AREAS, AND APPLY SAME TYPE PAINT AS USED IN SHOP. USE GALVANIZED REPAIR PAINT 4. ALL ASSEMBLING SHALL BE CLEANLY CUT, TRUE, AND TIGHTLY FITTED. OBSTRUCTIONS COMPLETELY AS SHOWN ON PLANS AND AS REQUIRED BY NEW CONSTRUCTION. ON DAMAGED GALVANIZED SURFACES. 5. ALL NAILING SHALL BE DONE IN SUCH A MANNER AS TO PREVENT ANY DAMAGE TO THE FINISHED 8. STRIPPING AND/OR REMOVAL OF EXISTING PAVING, CONCRETE PADS, CURBS, TREES, SHRUBS, SURFACES. EARTH, ETC. WITHIN NEW CONSTRUCTION AREA OR AS INDICATED. 9. OFF-SITE DISPOSAL OF ALL DEBRIS AND/OR EXCESS MATERIALS IN AN APPROVED AND LEGAL MANNER. 10.WHERE APPLICABLE LEVEL ALL EXISTING FLOORS AS REQUIRED TO RECEIVE NEW FLOOR COPYRIGHT © JORGE MASTROPIETRO ATELIER ARCHITECTS FINISHES. INSTALL REQUIRED TRANSITION PIECES BETWEEN VARIOUS FLOOR FINISHES SUITABLE FOR CONDITIONS AND ACCEPTABLE TO THE OWNER. MATCH EXISTING WHEREVER POSSIBLE.

PART 11 - SUPPLEMENTARY GENERAL CONDITIONS FOR MECHANICAL AND ELECTRICAL TRADES CONSTRUCTION NOTES G. DRYWALL PART 9 - FINISHES (WHERE APPLICABLE) 1. EXPOSED GYPSUM BOARD: ASTMC36 A. GENERAL A. GENERAL CONDITIONS: ALL GENERAL CONDITIONS AS SET FORTH PREVIOUSLY ARE HEREBY MADE A 1. GENERAL: A. TYPE X WHERE INDICATED AND WHERE REQUIRED FOR FIRE-RESISTANCE RATING INDICATED. 1. SEE GENERAL CONDITIONS PART OF THIS SPECIFICATION. ALL WORK TO BE COMPLETED IN ACCORDANCE WITH THE 2021 INTERNATIONAL BUILDING B. LONG EDGES: STANDARD TAPER 2. THE CONTRACTOR SHALL PROVIDE ALL ITEMS, MATERIALS ETC. AS SHOWN OR NOTED ON THE CODE - NJ EDITION, AND REGULATIONS OF ALL OTHER AGENCIES HAVING JURISDICTION. C. THICKNESS: 5/8", OR AS SHOWN ON DRAWINGS. DRAWINGS OR DESCRIBED HEREIN, INCLUDING LABOR, EQUIPMENT ANY OTHER ITEMS REQUIRED B. MATERIALS AND WORKMANSHIP: ALL WORK SHALL BE PERFORMED BY COMPETENT MECHANICS, 2. TRIM ACCESSORIES FOR THE COMPLETE INSTALLATION OF ALL FINISHES. ACCORDING TO MANUFACTURERS' RECOMMENDATIONS AND IN ACCORDANCE WITH ACCEPTED GOOD 2. MEANS OF EGRESS: A. PROVIDE MANUFACTURER'S STANDARD METAL TRIM ACCESSORIES, OF THE BEADED TYPE WITH A. THE OWNER SHALL BE RESPONSIBLE FOR FINAL SELECTION OF ALL FINISH MATERIALS AND PRACTICE OF THE VARIOUS TRADES. ALL MATERIAL SHALL BE AS SPECIFIED OR PERFECT CONDITION. ALL MEANS OF EGRESS SHALL BE MAINTAINED CLEAR AND FREE OF ALL OBSTRUCTIONS, FACE FLANGES FOR CONCEALMENT IN JOINT COMPOUND EXCEPT WHERE SEMI-FINISHING OR COLORS. WHERE

ONS, FACE FLANGES FOR CONCEALMENT IN JOINT COMPOUND EXCEPT WHERE SEMI-FINISHING OR COLORS. WHERE PARTICULAR ITEMS OF MATERIAL ARE SPECIFIED, CONTRACTORS SHALL SUPPLY THE BEST SUCH AS BUILDING MATERIALS, TOOLS, ETC. EXPOSED TYPE LOCATIONS. QUALITY ITEMS. B. CORNER BEADS AT EXTERNAL CORNERS B. MATERIALS 3. FIRE SAFETY: C. EDGE TRIM OF THE SHAPE INDICATED WHERE EDGE OF GYPSUM BOARD WOULD OTHERWISE 1. RESILIENT FLOOR COVERINGS SHALL BE INSTALLED IN THE LOCATIONS AS SHOWN AND NOTED ON C. SLEEVES: CONTRACTOR FOR EACH TRADE SHALL FURNISH ALL GALVANIZED STEEL PIPE SLEEVES AS A. ALL BUILDING MATERIALS WHICH ARE STORED AT THE SITE OR ANY AREA OF THE 1123 BROADWAY, SUITE 302, NY, NY 10010 BE EXPOSED OR SEMI- EXPOSED: L-TYPE FOR TIGHT ABUTMENT AT EDGES, OTHERWISE U-TYPE THE DRAWINGS. REQUIRED BY HIS WORK. BUILDING ARE TO BE STORED IN A LOCKED AREA. ACCESS TO THE AREA TO BE PHONE 646.248.6664 AS NEEDED/ REQUIRED. A. RESILIENT FLOORING CONTRACTOR SHALL INSPECT ALL SUBFLOORING AND IMMEDIATELY CONTROLLED BY THE GENERAL CONTRACTOR OR HIS REPRESENTATIVE. WWW.JMAPC.COM D. CONTROL JOINT UNITS, OF METAL AT LOCATIONS RECOMMENDED BY THE MANUFACTURER. REPORT FINDINGS TO THE OWNER. D. CUTTING AND PATCHING: CONTRACTOR FOR EACH TRADE SHALL BE RESPONSIBLE FOR ALL CUTTING B. ALL MATERIALS TO BE STORED IN A ORDERLY FASHION. 3. CONCEALED ACOUSTICAL SEALANT:

D. CUTTING AND PATCHING: CONTRACTOR FOR EACH TRADE SHALL BE RESPONSIBLE FOR ALL CUTTING B. ALL MATERIALS TO BE STORED IN A ORDERLY FASHION. 3. CONCEALED ACOUSTICAL SEALANT: NON-SHRINKING, NON- DRYING, NON-MIGRATING, NON- B. ALL FLOOR COVERINGS SHALL CONFORM TO ALL APPLICABLE FEDERAL SPECIFICATIONS. AND PATCHING AS REQUIRED BY HIS WORK. C. ALL FLAMMABLE MATERIALS TO BE KEPT TIGHTLY SEALED IN THEIR RESPECTIVE STAINING, MASTIC. C. ALL MATERIALS SHALL BE NEW AND FREE FROM DEFECTS; BEST COMMERCIAL GRADE FOR MANUFACTURERS' CONTAINERS. SUCH MATERIALS ARE TO BE KEPT AWAY FROM HEAT. 4. EXPOSED ACOUSTICAL SEALANT: LATEX, ACRYLIC, OR ACRYLIC-LATEX TYPE, PERMANENTLY EACH SPECIFIC FUNCTION AND SITUATION. E. MEASUREMENTS TO BE VERIFIED: BEFORE ORDERING ANY MATERIALS OR COMMENCING WITH ANY D. ALL FLAMMABLE MATERIALS TO BE USED AND STORED IN AN ADEQUATELY VENTILATED ELASTIC AND PAINTABLE. D. ALL PRIMERS AND ADHESIVES SHALL BE COMPATIBLE WITH FLOOR FINISH AS RECOMMENDED WORK, THE CONTRACTORS SHALL VERIFY ALL MEASUREMENTS AND CONDITIONS AT THE SITE AND SPACE. 5. JOINT TAPE: ASTM C475, PERFORATED BY THE MANUFACTURER. SHALL ASCERTAIN THE CORRECTNESS OF SAME. NO EXTRA CHANGE OR COMPENSATION WILL BE E. ALL ELECTRICAL POWER TO BE SHUT OFF WHERE THERE ARE EXPOSED CONDUITS. ARCHITECT: 6. JOINT COMPOUND: ASTM C 475, OF THE TYPE INDICATED. PROVIDE READY-MIXED VINYL-TYPE FOR E. VINYL BASES SHALL BE THE COVE TYPE AND SHALL BE .085" X 4" MOLDED VINYL. ALLOWED ON ACCOUNT OF DIFFERENCES BETWEEN ACTUAL DIMENSIONS / JOB CONDITIONS AND F. ALL ELECTRICAL POWER IN THE CONSTRUCTION AREA TO BE SHUT OFF AFTER INTERIOR WORK. PROVIDE 2 SEPARATE GRADES OF COMPOUND: ONE SPECIFICALLY FOR BEDDING 2. CERAMIC

S AND F. ALL ELECTRICAL POWER IN THE CONSTRUCTION AREA TO BE SHUT OFF AFTER INTERIOR WORK. PROVIDE 2 SEPARATE GRADES OF COMPOUND: ONE SPECIFICALLY FOR BEDDING 2. CERAMIC TILE (WHERE/ IF APPLICABLE ) THOSE INDICATED ON THE DRAWINGS. WORKING HOURS. JORGE E. MASTROPIETRO TAPE AND ONE FOR TOPPING. A. INSTALL CERAMIC TILE WHERE SHOWN ON THE PLANS AND IN ACCORDANCE WITH ALL G. CONTRACTOR, AT ALL TIMES, IS TO ENSURE THERE IS NO NATURAL GAS LEAKAGE IN NY LICENSE NO. 036208-1 7. INSTALLATION SHALL BE PERFORMED ONLY BY AN APPLICATOR EXPERIENCED IN USING THIS MANUFACTURES REQUIREMENTS AND ANSI STANDARDS. F. EXAMINATION OF DOCUMENTS, BUILDING AND SITE: THE BIDDERS ARE REQUIRED TO EXAMINE THE THE BUILDING, OR ANY FLAMMABLE GAS TO BE USED DURING CONSTRUCTION. PRODUCT AND SHALL USE TOOLS AND EQUIPMENT APPROVED BY THE MANUFACTURER. B. COLORS AND PATTERNS BY ARCHITECT/ OWNER. BUILDING AND SITE OF THE WORK AND TO EXAMINE AND BECOME FAMILIAR WITH PLANS, 8. INSTALL GYPSUM BOARDS IN LENGTHS AND DIRECTIONS WHICH WILL MINIMIZE NUMBER OF END C. CERAMIC TILES SHALL BE IN THE SHAPES AND SIZES AS SPECIFIED IN ELEVATIONS SPECIFICATIONS AND ALL OTHER CONTRACT DOCUMENTS PERTAINING TO THE PROPOSED WORK. 4. DUST CONTROL: JENNIFER PALERMO JOINTS, AND AVOID END JOINTS IN CENTRAL AREA OF CEILINGS. I. FURNISH COMBINATION COVE AND BASE COMPLETE WITH COMBINATION ANGLES AND SUBMISSION OF A BID SHALL BE SUFFICIENT TO ESTABLISH THE PRESUMPTION THAT THE BIDDER HAS DEBRIS, DIRT, AND DUST TO BE CLEANED UP AND CLEARED FROM THE BUILDING SITE NJ LICENSE NO. AI 015932 9. INSTALL WALLS AND PARTITIONS WITH EXPOSED GYPSUM BOARDS VERTICAL, WITH JOINTS STRETCHER SHAPES FOR

ANED UP AND CLEARED FROM THE BUILDING SITE NJ LICENSE NO. AI 015932 9. INSTALL WALLS AND PARTITIONS WITH EXPOSED GYPSUM BOARDS VERTICAL, WITH JOINTS STRETCHER SHAPES FOR INTERNAL AND EXTERNAL CORNERS AND ANY OTHER SHAPES AND INVESTIGATED THE SITE OF WORK AND IS SATISFIED AS TO ALL CONDITIONS ENCOUNTERED, THE DAILY TO AVOID EXCESSIVE ACCUMULATION. OFFSET ON OPPOSITE SIDES OF PARTITIONS. OTHERWISE, INSTALL BOARDS AT RIGHT-ANGLES WITH ACCESSORIES AS REQUIRED FOR THE COMPLETE INSTALLATION OF CERAMIC TILE. CHARACTER, QUALITY AND QUANTITY OF THE WORK TO BE PERFORMED, AND THE MATERIALS SUPPORTS, EXCEPT WHERE RECOMMENDED IN A DIFFERENT ARRANGEMENT BY MANUFACTURER. 3. PAINTING FURNISHED IN COMPLETION THEREOF. 5. PROTECTION 10. FORM CONTROL JOINTS WITH 1/2" SPACE BETWEEN BOARDS. INSTALL ACOUSTICAL SEALANT AT ALL SURFACES TO BE PAINTED SHALL BE CLEAN, PROPERLY PREPARED IN ACCORDANCE WITH PAINT A. CONTRACTOR TO PROVIDE ADJOINING PROPERTY PROTECTION IN ACCORDANCE WITH PROJECT: BASE OF SPACE, AND APPLY TRIM ACCESSORY AT FACE. MANUFACTURES PRINTED INSTRUCTIONS. PROTECT ADJACENT SURFACES AS NECESSARY. CLEAN G. TEMPORARY LINES: CONTRACTORS SHALL MAINTAIN CONTINUITY OF ALL SERVICES WITHIN THE CODE REQUIREMENT (NJAC 5:23-2.15 (f)1.I(1) & 5:23-2.34). 11. ACOUSTICAL SEALANT: DEMISING WALLS TO BE "SOUND RETARDING" WITH AN STC RATING OF 45 ALL DRIPS AND SPATTERS. COLOR AND GLOSS OF INTERIOR SPACES SHALL BE SELECTED BY THE BUILDING OR SITE DURING THE COURSE OF CONSTRUCTION, PROVIDING TEMPORARY LINES AS B. CONSTRUCTOR SHALL TAKE EVERY APPROPRIATE PRECAUTION IN ACCORDANCE WITH 262-270 MAIN STREET MIN.: APPLY 2 SEPARATE BEADS OF ACOUSTICAL SEALANT ALL AROUND AT INTERRUPTIONS OF OWNER. EXTERIOR PAINT COLORS SELECTED BY OWNER AND APPROVED BY ARCHITECT. THE REQUIRED. CURRENT BUILDING CODES AND

IOR PAINT COLORS SELECTED BY OWNER AND APPROVED BY ARCHITECT. THE REQUIRED. CURRENT BUILDING CODES AND CONSTRUCTION PRACTICES TO ENSURE ADJOINING WEST ORANGE DRYWALL WORK AS RECOMMENDED BY THE MANUFACTURER. PAINTING AND FINISHING OF ALL INTERIOR AND EXTERIOR ITEMS AND SURFACES SHALL BE AS PROPERTIES ARE PROTECTED FROM DAMAGE DURING DEMOLITION AND CONSTRUCTION. ESSEX COUNTY, NJ 07052 12. FORM "FLOATING" CONSTRUCTION FOR GYPSUM BOARDS AT INTERNAL CORNERS, EXCEPT FOLLOWS: H. SUPPORTS: SUPPORTS FOR ALL MECHANICAL AND ELECTRICAL EQUIPMENT REQUIRING SAME SHALL C. BEFORE COMMENCE ANY WORK THE CONSTRUCTOR SHALL NOTIFY THE NEIGHBOURS WHERE SPECIAL ISOLATION OF EDGE TRIM IS INDICATED. A. EXTERIOR WOOD AND TRIM SHALL RECEIVE 1 COAT OF PRIMER AND 2 FINISH COATS OF ALKYD BE FURNISHED BY RESPECTIVE CONTRACTORS. ALL EQUIPMENT HUNG FROM OVERHEAD ON BOTH SIDES PRIOR TO COMMENCEMENT OF ANY WORK. BLOCK 114 LOT 50 & 55 13. ISOLATE DRYWALL WORK FROM ABUTTING STRUCTURAL AND MASONRY WORK; PROVIDE EDGE OIL ENAMEL. CONSTRUCTION SHALL HAVE WEIGHT OF EQUIPMENT DISTRIBUTED BY USE OF ANGLE OR CHANNELED TRIM AND ACOUSTICAL SEALANT AS RECOMMENDED BY THE MANUFACTURER. B. EXTERIOR AND INTERIOR FERROUS METAL SHALL BE PROPERLY PRIMED AND GIVEN 2 COATS FROM SUPPORTS AS NECESSARY AND APPROVED, WITH SAME SUBSTANTIALLY FASTENED TO 14. INSTALL WATER-RESISTANT BACKING BOARDS WHERE SHOWN TO RECEIVE TILE AND SIMILAR OF ALKYD ENAMEL.