13026 Resubmission

FROM SUPPORTS AS NECESSARY AND APPROVED, WITH SAME SUBSTANTIALLY FASTENED TO 14. INSTALL WATER-RESISTANT BACKING BOARDS WHERE SHOWN TO RECEIVE TILE AND SIMILAR OF ALKYD ENAMEL. STRUCTURAL SUPPORT SYSTEM. ANY WALL-MOUNTED EQUIPMENT WHICH CANNOT BE SUPPORTED OWNER: RIGID APPLIED FINISHES. DO NOT APPLY TAPE AND COMPOUND AT JOINTS. SEAL CUT EDGE, JOINTS C. INTERIOR GYPSUM DRYWALL SHALL BE PROPERLY PRIMED AND GIVEN 1 COAT LATEX - SEE FROM ARCHITECTURAL OR STRUCTURAL MATERIALS, SHALL HAVE ITS OWN INDEPENDENT SUPPORT 262 MAIN STREET AND PENETRATIONS WITH WATER-RESISTANT SEALANT PRIOR TO INSTALLATION. FINISH SCHEDULE. SYSTEM FURNISHED BY THE CONTRACTOR. PROPER INSTALLATION METHOD SHALL BE AS APPROVED NJ IBC 2021 - SPECIAL INSPECTIONS REALTY LLC 15. SCREW GYPSUM BOARD TO SUPPORTS, JOINTS, STUDS, ETC. D. INTERIOR WOOD WORK, DOORS AND TRIM SHALL BE GIVEN 1 COAT SEMI-TRANSPARENT ALKYD- BY ARCHITECT. 16. EXCEPT AS OTHERWISE INDICATED, APPLY JOINT TAPE AND JOINT COMPOUND AT JOINTS (BOTH OIL STAIN AND 1 COAT POLYURETHANE BOTH SIDES, TOP AND BOTTOM. INSPECTION CODE 262-270 MAIN STREET DIRECTIONS) BETWEEN GYPSUM BOARDS. APPLY COMPOUND AT ACCESSORY FLANGES, E. INTERIOR EXPOSED CONCRETE FLOORS SHALL BE GIVEN 1 COAT OF CLEAR CONCRETE I. DAMAGED WORK: EACH CONTRACTOR SHALL PROTECT AND LEAVE IN PERFECT CONDITION ALL STEEL CONSTRUCTION IBC 1705.2 WEST ORANGE, NJ 07052 PENETRATIONS, FASTENER HEADS, AND SURFACE DEFECTS. SEALER-DUST PROOFING.

, NJ 07052 PENETRATIONS, FASTENER HEADS, AND SURFACE DEFECTS. SEALER-DUST PROOFING. MATERIALS, APPARATUS FITTINGS, FIXTURES AND TRIM IN THE SCOPE OF HIS CONTRACT. SHOULD ANY STRUCTURAL STEEL IBC 1705.2.1 646 427 9908 17. INSTALL COMPOUND IN 2 COATS (PLUS PREFILL OF CRACKS WHERE RECOMMENDED BY F. EXTERIOR STUCCO AND MASONRY SHALL BE GIVEN 2 COATS OF OIL BASED ENAMEL. ITEMS BE DAMAGED OR BROKEN, OR WORKMANSHIP MOLESTED, NO MATTER BY WHOM SUCH DAMAGE MANUFACTURER); SAND AFTER LAST COAT. G. PAINTS SHALL BE MANUFACTURED BY ONE OF THE FOLLOWING: BENJAMIN MOORE PAINTS CON- IS CAUSED, THE WORK MUST BE CORRECTED AND DAMAGED ITEMS REPLACED WITH NEW ITEMS, BY COLD FORMED STEEL DECK IBC 1705.2.2 18. APPLY SINGLE COAT USG IMPERIAL FINISH PLASTER, OR APPROVED EQUIVALENT, SMOOTH- LUX PAINT CO. OR EQUAL THE CONTRACTOR AT NO ADDITIONAL COST TO THE OWNER. ANY WORK WHICH NEEDS REDOING OPEN WEB STEEL JOIST GRIDERS IBC 1705.2.3 CONSULTANTS: TROWEL FINISH. BECAUSE CONTRACTORS RELATIVE TO DAMAGE SHALL BE DONE BY THE SKILLED TRADE WHICH COLD FORMED STEEL TRUSSES SPANING 60' OR GREATER IBC 1705.2.4 19. GENERAL STANDARD: GYPSUM ASSOCIATION SPECIFICATION GA-216, AND MANUFACTURER'S C. INSTALLATION ORIGINALLY PERFORMED SUCH WORK. ANY ADJUSTMENTS BETWEEN CONTRACTORS RELATIVE TO

TRAFFIC ENGINEER CONCRETE CONSTRUCTION IBC 1705.3 INSTRUCTIONS (WHICHEVER IS MORE STRINGENT). 1. ALL MATERIALS IN THIS SECTION SHALL BE INSTALLED IN THE MOST PROFESSIONAL AND DAMAGE TO WORK OR MATERIALS, SHALL NOT BE THE RESPONSIBILITY OF THE OWNER, ARCHITECT, WELDING OF REINFORCING BARS IBC 1705.3.1 DOLAN&DEAN 20. MATERIALS (USG OR APPROVED EQUAL) WORKMANLIKE MANNER, IN STRICT ACCORDANCE WITH THE MANUFACTURERS WRITTEN ENGINEER OR THEIR REPRESENTATIVES. MATERIAL TESTS IBC 1705.3.2 CONSULTING ENGINEERS, LLC INSTRUCTION AND ALL APPLICABLE CODES AND STANDARDS. 181 WEST HIGH STREET H. GUARANTEES:

181 WEST HIGH STREET H. GUARANTEES: 2. INSTALL ALL ACCESSORIES, TRIM PIECES, ETC. AS REQUIRED FOR THE COMPLETE INSTALLATION J. CHARTS AND TAGS: ALL VALVES, DAMPERS, CONTROLS SHALL BE DESIGNED BY DISTINGUISHING MASONRY CONSTRUCTION IBC 1705.4 1. MATERIALS: THE CONTRACTOR SHALL FURNISH TO THE OWNER A 5 YEAR WRITTEN GUARANTEE OF EACH FINISH MATERIAL. NUMBERS AND/OR LETTERS ON REQUIRED CHARTS AND/OR DIAGRAMS. THE CONTRACTOR SHALL GLASS UNIT MASONRY AND MASONRY VENEER IN RISK CATEGORY IV IBC 1705.4.1 SOMERVILLE, NJ 08876 ON ALL MATERIALS FURNISHED BY THOSE TRADES AS LISTED IN THIS SECTION TO BE FREE FROM 3. ALL MATERIALS SHALL BE ACCURATELY SCRIBED TO FIT PIPES, COLUMNS, AND ALL OTHER INSTALL APPROVED TAGS FOR ALL DESIGNATED ITEMS, WITH NUMBERS AND/OR LETTERS ON THE TAGS VERTICAL MASONRY FOUNDATION ELEMENTS IBC 1705.4.2 908 927 0100 DEFECTS DUE TO FAULTY WORKMANSHIP AND / OR MATERIALS. ALL DEFECTIVE MATERIAL SHALL BE FEATURES AND SHALL BE NEATLY CUT AND BUTTED TO ALL WALLS BASES, ETC. CORRESPONDING TO THOSE ON THE CHARTS AND/OR DIAGRAMS. SOILS IBC 1705.6 REPLACED AS REQUIRED IMMEDIATELY AFTER PROPER NOTICE, AT NO COST TO THE OWNER. 4. CERAMIC TILES SHALL BE SET PLUMB LEVEL AND TRUE TO LINE, ALL JOINTS SHALL BE UNIFORM; STRUCTURAL ENGINEER DRIVEN DEEP FOUNDATIONS IBC 1705.7 HUDSON ENGINEERING, LLC.

DRIVEN DEEP FOUNDATIONS IBC 1705.7 HUDSON ENGINEERING, LLC. 1/4" RUN THRU FROM FLOORS TO WALL AND FROM WALL TO WALL. K. MANUFACTURER'S INSTRUCTIONS: PROVIDE FOR EACH ITEM OF EQUIPMENT OR APPARATUS CAST-IN-PLACE DEEP FOUNDATIONS IBC 1705.8 A. ALL TILE SHALL BE SET IN ACCORDANCE WITH THE TILE COUNCIL OF AMERICA STANDARDS AND FURNISHED A COMPLETE SET OF PRINTED INSTRUCTIONS OBTAINED FROM THE MANUFACTURER 25 W8TH STREET, BSMT PART 7-THERMAL AND MOISTURE PROTECTION WITH AN EPOXY ADHESIVE EXCEPT AT EXTERIOR AND WET APPLICATIONS WHERE TILE SHALL BE COVERING OPERATION, CARE, LUBRICATION, CLEANING SERVICING, ADJUSTING, ETC., OF ITEMS HELICAL PILE FOUNDATIONS IBC 1705.9 DRY SET MORTAR. INVOLVED TOGETHER WITH SPECIAL SAFETY INSTRUCTIONS, PARTICULARLY INSTRUCT OWNER'S STRUCTURAL INTEGRITY OF DEEP FOUNDATION ELEMENTS IBC 1705.10 BAYONNE, NJ 07002 A. GENERAL B. GROUT SHALL BE PORTLAND

BAYONNE, NJ 07002 A. GENERAL B. GROUT SHALL BE PORTLAND CEMENT COMMERCIAL GRADE, COLOR SHALL BE WHITE AT ALL REPRESENTATIVE WHO WILL OPERATE PLANT IN ALL SUCH DETAILS. FABRICATED ITEMS IBC 1705.11 201 614 5304 1. SEE GENERAL CONDITIONS FLOORS AND WALLS. SPECIAL INSPECTIONS FOR SEISMIC RESISTANCE IBC 1705.13 2. SEE PART IV - MASONRY 5. PAINTING SHALL BE DONE BY THOSE SKILLED IN THEIR TRADE. APPLY ALL MATERIAL EVENLY. NO L. MANUFACTURER'S DIRECTIONS: THESE SHALL BE FOLLOWED IN ALL CASES WHERE MANUFACTURER TESTING FOR SEISMIC RESISTANCE IBC 1705.14 CIVIL ENGINEER SAGS, RUNS, CRAWLS, OR OTHER DEFECTS SHALL BE ALLOWED. FURNISHES DIRECTIONS COVERING POINTS

SAGS, RUNS, CRAWLS, OR OTHER DEFECTS SHALL BE ALLOWED. FURNISHES DIRECTIONS COVERING POINTS NOT SHOWN IN DRAWINGS AND SPECIFICATIONS. HUDSON ENGINEERING, LLC. B. MATERIALS A. ALL SURFACES TO BE PAINTED SHALL BE THOROUGHLY AND UNIFORMLY COVERED, APPLY SPRAYED FIRE-RESISTANT MATERIALS IBC 1705.15 1. ASPHALTIC BITUMINOUS TROWEL ON DAMPPROOFING FOR FOUNDATIONS AND BELOW GRADE NECESSARY COATS TO COMPLETE JOB. M. OPERATING, MAINTENANCE AND INSTRUCTION DATA: SUBMITTED TO THE OWNER FOR APPROVAL MASTIC AND INTUMESCENT FIR-RESISTANT COATINGS IBC 1705.16 25 W8TH STREET, BSMT MASONRY WALLS. PRIOR TO ACCEPTANCE OF INSTALLATION, COMPLETE AND AT ONE TIME. EXTERIOR INSULATION AND FINISH SYSTEM IBC 1705.17 BAYONNE, NJ 07002 2. CAULKING AND SEALANTS SHALL BE SELECTED BY THE CONTRACTOR TO SUIT CONDITIONS AND D. PROTECTION AND CLEANING WATER RESISTIVE BARRIER COATING IBC 1705.17.1 201 614 5304 MATERIALS. 1. ALL WORK SHALL BE PROTECTED BY A TEAR RESISTANT HEAVY WEIGHT KRAFT PAPER, TAPE ALL N. GUARANTEES: ALL WORK COMPLETED GUARANTEED FOR A MINIMUM OF ONE YEAR EXCEPT FOR EXTENDED PERIOD FOR COMPRESSORS, ETC.

EXTENDED PERIOD FOR COMPRESSORS, ETC. FIRE-RESISTANT PENETRATION & JOINTS IBC 1705.18 A. CAULKING AND SEALANTS TO MATCH SURROUNDING SURFACE COLORS. SEAMS. PAPER SHALL BE INSTALLED IN AREAS SUBJECT TO TRAFFIC WHICH WOULD BE DETRIMENTAL B. ALL MATERIALS SHALL BE CAREFULLY SELECTED FOR COMPATIBILITY WITH EACH OTHER IN TO THE FINISHED SURFACE. ALL COVERINGS SHALL REMAIN IN PLACE FOR THE DURATION UNTIL THE PENETRATION FIRESTOPS IBC 1705.18.1 EACH JOINT SYSTEM. BUILDING IS READY FOR OCCUPANCY. FIRE-RESISTANT JOINT SYSTEM IBC 1705.18.2 C. ALL MATERIALS SHALL BE INSTALLED AS PER THE MANUFACTURERS WRITTEN INSTRUCTIONS. 2. EACH TRADE SHALL THOROUGHLY CLEAN AND MAKE GOOD ALL WORK IN THEIR CONTRACT. TESTING FOR SMOKE CONTROL IBC 1705.19 3. INSULATION SHALL BE INSTALLED IN THE TYPES AND SHAPES AS SHOWN ON THE DRAWINGS AND REMOVE ALL TRACES OF GROUT, DIRT, GREASE, ETC. TO THE SATISFACTION OF THE OWNER. SEALING OF MASS TIMBER IBC 1705.20 AS FOLLOWS: A. FIBERGLASS ROLLS OR BATTS FACED WITH ALUMINUM FOIL VAPOR RESISTANT MEMBRANE E. GUARANTEES WITH INTEGRAL NAILING FLANGES. 1. MANUFACTURERS AND CONTRACTORS SHALL GUARANTEE ALL WORK FOR A PERIOD OF 2 YEARS

OF 2 YEARS ARCHITECT'S SEAL: I. EXTERIOR WALLS: 3 1/2", R-13 MIN. WHERE SHOWN OR NOTED ONLY. FROM DATE OF FINAL ACCEPTANCE. ALL WORKMANSHIP AND MATERIALS SHALL BE FREE FROM II. PROVIDE UNFACED BATTS AT INTERIOR PARTITION WALLS AND CEILINGS IN THE SIZES AS DEFECTS. ALL REPAIRS SHALL BE PROMPTLY MADE. SHOWN ON THE DRAWINGS WHERE SHOWN OR REQUIRED FOR SOUND ABSORPTION 2. CONTRACTORS SHALL PROVIDE OWNER WITH SURPLUS STOCK OF ALL FINISH PRODUCTS. REQUIREMENTS. 3. IN THE EVENT ANY ADJACENT AREAS DAMAGED AS THE RESULT OF THE FAILED PRODUCT THE III. ROOFS AND CEILINGS UNDER UNHEATED SPACES: 9", R-30 DAMAGED WORK SHALL BE REPAIRED AT NO COST TO THE OWNER. INCLUDED ALSO SHALL BE B. RIGID INSULATION SHALL BE INSTALLED IN THE SIZES AS SHOWN ON THE DRAWINGS, SHALL BE ADJACENT AREAS WHICH MUST BE DISTURBED IN ORDER TO REPAIR DEFECTIVE MATERIALS. EXTRUDED AND HAVE AN "R" VALUE OF 5 PER INCH. I. INSULATION SHALL BE "STYROFOAM" BRAND AS MANUFACTURED BY THE DOW CHEMICAL CO. OR EQUAL. PART 10 - SPECIALTIES (NOT USED) 4. PROVIDE A TOTAL ROOF DRAINAGE SYSTEM AS SHOWN OR REQUIRED, INCLUDING, BUT NOT LIMITED TO GUTTERS, LEADERS, CHIPS, CLEATS, CAPS, ROOF DRAINS, ETC. A. PREFINISHED COLOR AS SELECTED, ALL MATERIALS SHALL MATCH. B. 0.04" ALUMINUM GUTTER, PROFILE AND SIZES AS SHOWN ON DRAWINGS. (EXPANSION JOINTS AS REQUIRED TO PREVENT BUCKLING) C. 0.04" ALUMINUM DOWNSPOUT, PROFILE AND SIZES AS REQUIRED, TIE TO UNDERGROUND DRAINAGE SYSTEM. PROGRESS DATE: 29-01-2026 D. ALUMINUM

PROGRESS DATE: 29-01-2026 D. ALUMINUM HANGERS FOR GUTTER AND STRAPS FOR DOWN SPOUTS, SIZES AS REQUIRED FOR JOB APPLICATION. JM E. ALL ACCESSORIES, MITERS, SLIP JOINTS, CONNECTIONS, END CAPS, ELBOWS, EXPANSION PRINCIPAL IN CHARGE JOINTS, ETC. F. 0.20" FLASHING AND COUNTER FLASHING. CC PROJECT TEAM G. SEALING OF ALL JOINTS AS PER MANUFACTURER'S RECOMMENDATIONS. 5. FLASHINGS SHALL BE INSTALLED WHERE NOTED OR REQUIRED. JM A. ALL FLASHINGS AND ACCESSORIES SHALL BE OF CORROSIVE RESISTANT MATERIALS.