242-22 Attachment - RFP Ginny Duenkel Underwater Lighting Improvements.pdf

4. Using a number three (3) Phillips head screwdriver loosen the screw and remove uni-tension wire clamp from the face ring. 5. Remove the face ring and wire clamp from the light housing and set aside for installation later. Note: A 120 VAC to 12 VAC external transformer is required for the 12 VAC model IntelliBrite LED Spa light. See page 9 for more information. Loosen the Phillips screw to remove wire clamp Note: The IntelliBrite Spa Light fixture is a sealed light assembly which is replaceable. The lens, gasket and face ring can be removed from the sealed light assembly for replacement. See page 15 for replacement kit part numbers. IntelliBrite spa light fixture with lens, gasket and face ring attached 6. With the light assembly resting on its base, carefully pry off the gasket to release the lens. Discard the gasket. ANEW LENS GASKET MUST BE USED EACH TIME THE SPA LED LIGHT IS REASSEMBLED 7. Disconnect the IntelliBrite Spa LED light assembly cable from the junction box and discard the light assembly. IntelliBrite® Pool and Spa White LED Light Installation and User’s Guide

8. INSTALLING THE INTELLIBRITE SPA LED WHITE WITH NEW GASKET: Install a new gasket during reassembly of the IntelliBrite spa LED white light. A NEW LENS GASKET MUST BE USED EACH TIME THE LIGHT IS REASSEMBLED. 9. Install the new gasket onto the lens: a) With the light housing resting on its base, place the lens then the gasket on top of the light housing. b) Place the face ring on top of the gasket. Make sure that the lens and gasket are centered correctly on the light housing. ¢) Aligning the face ring and lens: Align the face ring and lens so that the letter “O” in the word “TOP" and the small arrow above it) on the surface of the lens points to the pilot screw hole on the face ring. d) Aligning the lens position with the LEDs: While looking through the front of the lens, slightly rotate the lens until the vertical lines on the lens are in focus with the four (5) rows of LEDs below. Pilot screw Align letter “O” in the word “TOP” on lens with pilot screw hole on face ring Align vertical line ‘on lens with rows of LEDs under lens IntelliBrite® Pool and Spa White LED Light Installation and User’s Guide

10. With the hook ends of the circular uni-tension wire clamp pointing down, spread the clamp and place it in the “U" recesses of the locking levers. Be sure the hook ends of the wire clamp are located between the pair of locking levers as. shown below and that the clamp is properly engaged with all of the lock levers. 11. Place a cloth on the ground to protect the lens. Turn the light over so the lens is resting on the cloth. Tighten the bolt and nut until the distance between the ends of the clamp equals ‘4-in or less. 12, PROCEED TO “Replacing the IntelliBrite White LED Light Assembly (in an existing pool or spa)” on page 16 for spa light assembly installation instructions. Orientation of bolt and wire clamp Pilot Screw Tighten nut and bolt about 90° from the Pilot Screw between the lock levers, IntelliBrite ‘Spa light assembly \ we Hook ends. : wire clamp . oon and Lock lever bolt (x4), Gasket Lg Face ring Pilot screw IntelliBrite® Pool and Spa White LED Light Installation and User's Guide

IntelliBrite Spa Light Replacement Kit Numbers Pilot | Face Ring. Captive gum Y Washer | Uni-tension oa wire clamp Lens Gasket ——— Kit Part No. Description 640045 Face ring assembly, stainless steel - Uni-tension wire clamp assembly - Gasket, 4 in diameter, off white 640046 Gasket, 4 in diameter, off white ~ Lens, IntelliBrite, Spa, 4 in diameter, tempered 79104800 Pilot screw, with captive gum washer 79108500 - Gasket, 4 in diameter, off white Note: A 120 VAC to 12 VAC external transformer is required for the 12 VAC model IntelliBrite LED Spa light. See page ii for more information. IntelliBrite® Pool and Spa White LED Light Installation and User’s Guide

16 Replacing the IntelliBrite Pool or Spa White LED Light Assembly (in an existing pool or spa) Risk of Electrical Shock or Electrocution! This underwater light must be installed by a licensed or certified electrician or a qualified pool professional in accordance with the National Electrical Code and all applicable local codes and ordinances. Improper installation will create an electrical hazard which could result in death or serious injury to pool users, installers or others due to electrical shock, and may also cause damage to property. ADANGER | 72 ‘ Always disconnect the power to the pool light at the circuit breaker before servicing the light. Failure to do so could result in death or serious injury to serviceman, pool users or others due to electrical shock. Verify that the pool and spa meets the requirements of the current National Electrical Code and all local codes and ordinances. A licensed or certified electrician must install the electrical system to meet or exceed those requirements before the underwater light is installed. Some of the requirements of the National Electrical Code which the pool's electrical system must meet are as follows: * The lighting circuit has a Ground Fault Circuit Interrupter (GFCI) for line voltage models, and has an appropriately rated circuit breaker. * — The Junction Box (or, for 12 volt models, the low voltage transformer) is located at least eight (8) inches above ground level and at least 48 inches from the edge of the pool; see Figure 1 on page 3. ¢ The light fixture and all metal items within five (5) feet of the pool are properly electrically bonded. * — The wet niche is properly installed so that the top edge of the underwater light’s lens is at least 18 inches below the surface of the water in the pool; see Figure 1 on page 3. * The wet niche is properly electrically bonded and grounded via the No. 8 AWG ground connector located at the rear of the niche; see Figure 1. Note: The poo! and spa electrical system can be verified with a Pool and Spa Electrical Qualification Test Kit. The test kit is available from Pentair Water Pool and Spa. The electrical system inspection using this kit must be performed by trained and certified personnel. *. To be certain that the pool's electrical system meets all applicable requirements, the electrician should also consult the local building department. « — Use

d by trained and certified personnel. *. To be certain that the pool's electrical system meets all applicable requirements, the electrician should also consult the local building department. « — Use only Pentair Poo! Products® wet niches to insure proper bonding and grounding connections. IntelliBrite® Pool and Spa White LED Light Installation and User’s Guide

17 Replacing the IntelliBrite Pool or Spa White LED light (after electrical requirements are met) The following installation instructions describe how to install the IntelliBrite white pool and spa LED light assembly after completing the LED light engine removal and replacement procedures. Refer to: IntelliBrite Pool White LED Light Removal and Installation instructions, on page 5. ' IntelliBrite Spa White LED Light Gasket, Face Ring and Lens Removal and Installation instructions, on page 11. Failure to bring the pool or spa’s electrical system up to code requirements before installing the underwater light will create an electrical hazard which could result in death or serious injury to pool users, installers, or others due to electrical shock, and may also cause damage to property. WARNING! Switch off main electrical switch or circuit breaker, and the switch which operates the IntelliBrite underwater light. To remove light fixture assembly from the pool. Remove the special bronze pilot screw at top of face ring. Remove the IntelliBrite light assembly from the niche and place it on the deck. Remove Junction Box cover, disconnect the light fixture wires, and pull the cord through the conduit. Feed the new light fixture cord through the conduit from the niche to the Junction Box. Note: Depending on the length of the conduit, special tools may be required to pull the cord through the conduit. Leave at least four (4) feet of cord to coil around the light fixture; see Figure 1 on page 3. This four (4) feet of cord coiled around the light allows the light to be serviced after the pool is filled with water. Cut the cord at the Junction Box, leaving at least size (6) inches of cord to make connections. Strip six (6) inches of the outer cord jacket from the cord to expose the three insulated wires — Be careful not to damage the insulation on the three inner wires. Connect all three wires to the corresponding circuit wires in the Junction Box (black wire to power, white wire to common, and green wire to ground) and secure the Junction Box cover in place. TntelliBrite® Pool and Spa White LED Light Installation and User’s Guide

18 Never operate this underwater light for more than ten (10) seconds unless it is totally submerged in water. Without total submersion, the light assembly will get extremely hot, which may result in serious burns or in breakage of the lens. This may result in serious injury to pool users, installers, or bystanders, or in damage to property. 9. Install the IntelliBrite light assembly into the niche and tighten the special bronze pilot screw. Use only the special pilot screw provided with this underwater light. This screw mounts and electrically grounds the housing securely to the mounting ring and wet niche. Failure to use the screw provided could create an electrical hazard which could result in death or serious injury to pool users, installers or others due to electrical shock. Pilot screw Pilot screw IntelliBrite Pool White LED Light IntelliBrite Spa White LED Light 10. Fill the pool/spa until the IntelliBrite underwater LED light is completely submerged in water before operating the light for more than ten (10) seconds. Note: The light should never be powered on out of the water for more than 10 seconds. Switch on main switch or circuit breaker, as well as the switch which operates the underwater light itself to verify that the light is operating correctly. IntelliBrite® Pool and Spa White LED Light Installation and User’s Guide

Notes IntelliBrite® Pool and Spa White LED Light Installation and User's Guide

> Pentair Water Pool and Spa” AT P/N 619838 Rev B